Génie de Procédés

This paper refines and validates the predictions of a simplified analysis method for evaluating the potential of daylighting to save energy use associated with electrical lighting. Specifically, impacts on daylighting performance are investigated for several combinations of building geometry, window size, and glazing type for several US and international locations. The impact of both dimming and stepped daylighting controls and their settings are also investigated. Predictions from the simplified method are validated using measurements obtained from field-testing of a daylighting control system utilized to operate lighting fixture illuminating an office space.

In this study, Al-doped zinc oxide (AZO) nanostructures are prepared on polycrystalline fluorine-doped tin oxide (FTO)-coated conducting glass substrates from nitrates baths by the electrodeposition process at 70 °C. The electrochemical, morphological, structural and optical properties of the AZO nanostructures were investigated in terms of different Al concentration in the starting solution. It was found from the Mott–Schottky (M-S) plot that the carrier density of AZO nanostructures varied between 3.1110 20 to 5.5610 20 cm-3 when the Al concentration was between 0 and 5 mM. Atomic force microscopie (FM) images reveal that the concentration of Al has a very significant influence on the surface morphology and roughness of AZO thin films. X-ray diffraction (XRD) patterns demonstrate preferential (002) crystallographic orientation having c-axis perpendicular to the surface of the substrate and average crystallites size of the films was about 23–36 nm. As compared to pure ZnO, Al-doped ZnO exhibited lower crystallinity and there is a shift in the (002) diffraction peak to higher angles. ZnO nanostructures were found to be highly transparent and had an average transmittance of 80 % in the visible range of the spectrum. After the incorporation of Al content into ZnO the average transmittance increased and the band-gap tuning was also achieved (from 3.22 to 3.47 eV).

Al-doped zinc oxide (AZO) thin films are prepared on polycrystalline fluorine-doped tin oxide-coated conducting glass substrates from nitrates baths by the elec-trodeposition process at 70 °C. The electrochemical, morphological , structural and optical properties of the AZO thin films were investigated in terms of different Al concentration in the starting solution. It was found that the carrier density of AZO thin films varied between-3.11 and-5.56 9 10 20 cm-3 when the Al concentration was between 0 and 5 at.%. Atomic force microscopy images reveal that the concentration of Al has a very significant influence on the surface morphology and roughness of thin AZO. X-ray diffraction spectra demonstrate preferential (002) crystallographic orientation having c-axis perpendicular to the surface of the substrate and average crystallites size of the films was about 33–54 nm. With increasing Al doping, AZO films have a strong improved crystalline quality. As compared to pure ZnO, Al-doped ZnO exhibited lower crystallinity and there is a shift in the (002) diffraction peak to higher angles. Due to the doping of Al of any concentration , the films were found to be showing [80 % transparency. As Al concentration increased the optical band gap was also found to be increase from 3.22 to 3.47 eV. The room-temperature photoluminescence spectra indicated that the introduction of Al can improve the intensity of ultraviolet (UV) emission, thus suggesting its greater prospects in UV optoelectronic devices. A detailed comparison and apprehension of electrochemical, optical and structural properties of ZnO and ZnO:Al thin films is done for the determination of optimum concentration of Al doping.

Zinc oxide (ZnO) nanostructures were deposited under potentiostatic control on indium tin oxide coated glass substrate from an aqueous solution containing zinc nitrates. Voltammograms were recorded to determine the optimal potential region for the depo-sition of ZnO. The deposition was carried out at various concentrations of Zn ?2 and constant bath temperature (65 °C). The nucleation and growth kinetics at the initial stages of ZnO studied by current transients indicated a 3D island growth (Volmer–Weber). It is characterized by an instantaneous nucleation mechanism followed by diffusion-limited growth. The Mott–Schottky measurements , the flat band potential and the donor density for the ZnO nanostructures were determined. The morphological , structural, and optical properties of the nano-structures have been investigated. Scanning electron microscopy images showed different sizes and morphologies of the nanostructures which depends on the concentrations of Zn ?2. X-ray diffraction study confirms the wurtzite phase of the ZnO nanostructures with high crystallinity. UV–visible spectra showed a significant optical transmission (up to 90 %), which decreased with Zn 2? concentrations. The energy band gap values have been estimated to be in the range 3.36–3.54 eV.

The present investigation addressed the entropy generation, fluid flow, and heat transfer regarding Cu-Al 2 O 3 -water hybrid nanofluids into a complex shape enclosure containing a hot-half partition were addressed. The sidewalls of the enclosure are made of wavy walls including cold isothermal temperature while the upper and lower surfaces remain insulated. The governing equations toward conservation of mass, momentum, and energy were introduced into the form of partial differential equations. The second law of thermodynamic was written for the friction and thermal entropy productions as a function of velocity and temperatures. The governing equations occurred molded into a non-dimensional pattern and explained through the finite element method. Outcomes were investigated for Cu-water, Al 2 O 3 -water, and Cu-Al 2 O 3 -water nanofluids to address the effect of using composite nanoparticles toward the flow and temperature patterns and entropy generation. Findings show that using hyb...

A numerical study of combined natural convection and radiation in a square cavity filled with a gray non-scattering semi-transparent fluid is conducted. The horizontal walls are adiabatic and the vertical are differentially heated. Convection is treated by the finite volumes approach and the discrete ordinates method is used to solve radiative transfer equation using S6 order of angular quadrature. Representative results illustrating the effects of the Rayleigh number, the optical thickness and the Planck number on the flow and temperature distribution are reported. In addition, the results in terms of the average Nusselt number obtained for various parametric conditions show that radiation modifies significantly the thermal behavior of the fluid within the enclosure.

Numerical investigation of combined laminar natural convection and volumetric radiation with internal heat generation is presented in this paper and computations are performed for a grey gas-filled square cavity whose horizontal walls are adiabatic and vertical walls are differentially heated. The convection is treated under Boussinesq approximation by an approach based on finite-volumes and the volumetric radiation by the discrete ordinates method. Flow and heat transfer characteristics through isotherms, streamlines and average Nusselt numbers have been presented for an external Rayleigh number 106, internal Rayleigh number 0 to 4x1012, optical thickness 0 to 10 and Albedo 0 to 1. Representative results illustrating the effects of the optical thickness and the internal heat generation on the flow and the temperature distribution within the cavity are presented. The results reveal that the fluid flow and heat transfer are influenced significantly by the volumetric radiation and the...