Alignment Basics: Three terms to understand when getting an alignment | PCA Tech Tips
Recently, we have done quite a bit of work to Projekt 964. KW Suspension sent us a full set of adjustable coil-overs that TPC Racing in Jessup, Maryland installed for us. Additionally, Recaro sent us a pair of Pole Position seats with very retro-looking upholstery. We were lucky to have extra material sent to cover the rear seats to match. HRE wheels sent over a stunning set of lightweight wheels that totally changed the look of the 964. The wheels were also upgraded from the stock 16-inch diameter to beefier 18-inchers. With the suspension and wheel changes complete, we returned to TPC Racing to have the ride height adjusted and the car aligned. Standard procedure when installing all-new suspension.

Projekt 964 was far out of alignment after installing coil-overs.
Even if you haven’t changed your suspension, you should plan on having the alignment checked at least once a year. With the tire alignment systems at shops today, it takes more time to set up the equipment and line up the car than checking the alignment. If the car is out of alignment, a qualified technician is needed to bring the car’s spec back to new Once the alignment machine is set up, they usually go fairly quickly. If you’re thinking of having your car aligned, here are three terms you’ll see on your alignment report. While not all three things are fully adjustable on all cars, they do affect the alignment and thus your car’s handling.

The 964 has semi-trailing arms at the rear, the alignments of which are adjusted by this group of nuts and bolts. The alignment shop will likely mark the original settings and adjust from there. This is after the adjustment.
TPC Racing first asked us what we planned to do with the car. We told them that it was a street car that will be used for tours and the occasional autocross. With that knowledge, they set the alignment to the appropriate settings.
Here are the Three terms you need to understand when getting your car aligned.
Camber

You can see the negative camber on the left rear wheel, which tilts inward at the top.
You know it once you’ve seen it. When you’re either looking from behind or head on, the tires may seem tilted. Normally, you will see the top of the tire tilted inwards toward the car. This is called negative camber. The amount of tilt is measured in degrees. When the top of the tire is tilted away from the car, it is called positive camber. Most cars use negative camber to improve handling in corners. While straight line grip is a bit reduced, the benefit and using the entire tread while cornering far outweighs the slight loss of grip in a straight line. Too much negative camber and you’ll see excess wear on the inside of the tire. A better way to find out whether you have the correct amount of negative camber is to check the tires’ temperatures in three places: Outside, middle, and inside. Directly after a track or autocross session, check the tires’ temps. Too little negative camber will see higher temps on the outside than the middle or inside. Too much negative camber and the insides will be hottest. If the temps are fairly even across the tire, then you probably have the correct amount of negative camber.
Toe
It’s hard to believe, but tires aren’t always pointing straight when you are driving in a straight line. Toe measurement is done by comparing the distances on a pair of tires based on the car’s centerline when viewed from above. What reason would there be for the tires not to be straight when going in a straight line? Changing toe angle can drastically change the handling characteristics of the car. All cars have adjustable front toe. Toe-in is when the front of the tires are closer to the centerline than the rears, and toe out is when the fronts are further away from the centerline than the rears. Porsches generally have adjustable toe in the front and the rear, though the majority of modern passenger cars have no rear toe adjustability.
Caster
When viewing the car’s side profile with regards to the front wheels, caster is how far forward or behind the steering pivot angle is to the vertical axis, which can be drawn straight up from the center of the wheel. It’s measured in degrees, and you’ll hear the terms positive caster, negative caster, or neutral caster. For safety reasons, most modern cars have positive caster.
PCA’s Tech Tactics Live did a Alignment 101 where these three terms and more are discussed.
Want to receive more great Porsche content?
Subscribe to e-Brake News
Related Stories:
» Circuit of the Americas 2026 | PCA Club Racing LIVE on PCA's YouTube Nov. 21-22» From the Regions | November 16-22, 2026
» From the Regions | November 9-15, 2026
» 1998 Porsche Boxster, 2003 911 Carrera Cabriolet, 2003 Carrera 4S, or 2004 911 40th? | Mart Fresh
» ünStock 2026: Porsches on the Pier! We highlight 16 of 'em | PCA Spotlight



