ひとまずおおよそ組み上がったのでfactoryとしてのinitramfsイメージのテスト。
この機種においても既にサポート済みのWN-DX1167R, WN-AX1167GR2, WN-AX2033GRと同様の構造となっているため、initramfsイメージをstockのWebUIから投入したうえでsysupgradeイメージによりsysupgradeを実施する必要がある。
initramfsイメージからのsysupgrade時にbootnumとdebugflagのチェックを行い、bootnumが “2” である場合は “1” に、debugflagが “0” である場合は “1” に自動的に変更する。
### DO NOT set cfgapply ### ### Checksum is the same but commit does not change anything! Do nothing! ### [ 510.424000] led=9, on=1, off=1, blinks,=1, reset=0, time=4000 low_trigger=0 update cfg_1_chksum Unlocking persist ... update cfg_2_chksum Unlocking persist ... update cfg_1_size Unlocking persist ... update cfg_2_size Unlocking persist ... Unlocking firmware_2 ... Writing from /tmp/fw.bin to firmware_2 ... Header checksum OK. Data checksum OK Unlocking persist ... ### Switch to bank 2 on next boot! ### procd: - shutdown - [ 517.052000] br-lan: port 3(rai0) entered disabled state [ 517.064000] br-lan: port 2(ra0) entered disabled state [ 517.076000] br-lan: port 1(eth0) entered disabled state [ 517.084000] device eth0 left promiscuous mode [ 517.096000] br-lan: port 1(eth0) entered disabled state [ 517.104000] ra2880stop()...Done [ 517.112000] eth1: ===> VirtualIF_close [ 517.120000] Free TX/RX Ring Memory! [ 517.128000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 517.140000] device ra0 left promiscuous mode [ 517.148000] br-lan: port 2(ra0) entered disabled state [ 517.160000] device rai0 left promiscuous mode [ 517.168000] br-lan: port 3(rai0) entered disabled state [ 517.236000] eth1: ===> VirtualIF_close [ 517.244000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 518.572000] MTPciPollTxRxEmpty [ 519.196000] AsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0x0 [ 519.204000] RTMPSetPiggyBack(957): Not support for HIF_MT yet! [ 519.224000] RT28xxPciAsicRadioOff(): Not support for HIF_MT yet! [ 519.236000] RTMPDrvClose call RT28xxPciAsicRadioOff fail !! [ 519.248000] tx_kickout_fail_count = 0 [ 519.252000] tx_timeout_fail_count = 0 [ 519.260000] rx_receive_fail_count = 0 [ 519.268000] alloc_cmd_msg = 96 [ 519.276000] free_cmd_msg = 96 [ 520.648000] Device Instance [ 520.656000] WDEV 00: Name:rai0 [ 520.664000] Wdev(list) Idx:0 [ 520.668000] Idx:13 [ 520.672000] WDEV 01: Name:rai1 [ 520.680000] Wdev(list) Idx:1 [ 520.688000] Idx:14 [ 520.692000] WDEV 02: Name:rai2 [ 520.696000] Wdev(list) Idx:2 [ 520.704000] Idx:15 [ 520.708000] WDEV 03: Name:rai3 [ 520.716000] Wdev(list) Idx:3 [ 520.720000] Idx:16 [ 520.728000] WDEV 04: Name:apclii0 [ 520.732000] Wdev(list) Idx:4 [ 520.740000] Idx:17 [ 520.744000] WDEV 05: Name:wdsi0 [ 520.752000] Wdev(list) Idx:5 [ 520.756000] Idx:18 [ 520.760000] WDEV 06: Name:wdsi1 [ 520.768000] Wdev(list) Idx:6 [ 520.776000] Idx:19 [ 520.780000] WDEV 07: Name:wdsi2 [ 520.784000] Wdev(list) Idx:7 [ 520.792000] Idx:20 [ 520.796000] WDEV 08: Name:wdsi3 [ 520.804000] Wdev(list) Idx:8 [ 520.808000] Idx:21 [ 520.816000] WDEV 09: [ 520.820000] WDEV 10: [ 520.824000] WDEV 11: [ 520.828000] WDEV 12: [ 520.832000] WDEV 13: [ 520.836000] WDEV 14: [ 520.840000] WDEV 15: [ 520.844000] WDEV 16: [ 520.852000] WDEV 17: [ 520.856000] WDEV 18: [ 520.860000] WDEV 19: [ 520.864000] WDEV 20: [ 520.868000] WDEV 21: [ 520.876000] rai0: ===> main_virtual_if_close [ 520.888000] wifi_sys_linkdown(), wdev idx = 0 [ 520.896000] ExtEventBeaconLostHandler::FW LOG, Beacon lost (50:41:b9:**:**:09), Reason 0x10 [ 520.912000] Beacon lost - AP disabled!!! [ 520.924000] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 [ 520.948000] wifi_sys_close(), wdev idx = 0 [ 520.956000] APStop(), oper(0) bssid(0)=50:41:b9:**:**:09 [ 520.968000] AsicSetPreTbtt(): NotSupportedFunc for this arch(HIF_MT)! [ 520.980000] MtAsicSetPiggyBack(590): Not support for HIF_MT yet! [ 520.992000] AsicDisableSync(): NotSupportedFunc for this arch(HIF_MT)! [ 521.004000] asic_bss_beacon_exit(): NotSupportedFunc for this arch(HIF_MT)! [ 521.020000] wifi_sys_close(), wdev idx = 0 [ 521.028000] ap_ftkd> Release FT KDP Module... [ 521.036000] AsicDisableBeacon(): NotSupportedFunc for this arch(HIF_MT)! [ 521.036000] AsicSetPreTbtt(): NotSupportedFunc for this arch(HIF_MT)! [ 521.036000] MtAsicSetPiggyBack(590): Not support for HIF_MT yet! [ 521.036000] AsicDisableSync(): NotSupportedFunc for this arch(HIF_MT)! [ 521.036000] asic_bss_beacon_exit(): NotSupportedFunc for this arch(HIF_MT)! [ 521.040000] wifi_sys_close(), wdev idx = 1 [ 521.040000] AsicSetPreTbtt(): NotSupportedFunc for this arch(HIF_MT)! [ 521.040000] MtAsicSetPiggyBack(590): Not support for HIF_MT yet! [ 521.040000] AsicDisableSync(): NotSupportedFunc for this arch(HIF_MT)! [ 521.040000] asic_bss_beacon_exit(): NotSupportedFunc for this arch(HIF_MT)! [ 521.044000] wifi_sys_close(), wdev idx = 2 [ 521.044000] AsicSetPreTbtt(): NotSupportedFunc for this arch(HIF_MT)! [ 521.044000] MtAsicSetPiggyBack(590): Not support for HIF_MT yet! [ 521.044000] AsicDisableSync(): NotSupportedFunc for this arch(HIF_MT)! [ 521.044000] asic_bss_beacon_exit(): NotSupportedFunc for this arch(HIF_MT)! [ 521.048000] wifi_sys_close(), wdev idx = 3 [ 521.048000] AsicDisableSync(): NotSupportedFunc for this arch(HIF_MT)! [ 521.056000] CmdReStartDLRsp: WiFI FW Download Success [ 521.068000] RT28xxPciAsicRadioOff(): Not support for HIF_MT yet! [ 521.068000] RTMPDrvClose call RT28xxPciAsicRadioOff fail !! [ 521.068000] tx_kickout_fail_count = 0 [ 521.068000] tx_timeout_fail_count = 0 [ 521.068000] rx_receive_fail_count = 0 [ 521.068000] alloc_cmd_msg = 2192 [ 521.068000] free_cmd_msg = 2192 [ 521.068000] cut_through_token_list_destroy(): 86092d08,86092d08 [ 521.072000] cut_through_token_list_destroy(): 86092d18,86092d18 [ 521.072000] AsicResetWPDMA(): NotSupportedFunc for this arch(HIF_MT)! [ 521.072000] fw_own(): Write 1 to MT_CONN_HIF_ON_LPCTL bit 0 to set FW own [ 521.076000] RTMP_AllTimerListRelease: Size=36 [ 521.076000] RTMP_AllTimerListRelease: Cancel timer obj c373b8b8! [ 521.076000] RTMP_AllTimerListRelease: Timer is allocated by scan_partial_init+0x48/0x58 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.076000] RTMP_AllTimerListRelease: Cancel timer obj c373b878! [ 521.076000] RTMP_AllTimerListRelease: Timer is allocated by sync_fsm_init+0x248/0x2d8 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.076000] RTMP_AllTimerListRelease: Cancel timer obj c34ef020! [ 521.076000] RTMP_AllTimerListRelease: Timer is allocated by WscInitClientTimers+0x5c/0xb8 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.076000] RTMP_AllTimerListRelease: Cancel timer obj c348dce8! [ 521.076000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x7c/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.080000] RTMP_AllTimerListRelease: Cancel timer obj c348dd1c! [ 521.080000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x94/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.080000] RTMP_AllTimerListRelease: Cancel timer obj c3492654! [ 521.080000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x7c/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.080000] RTMP_AllTimerListRelease: Cancel timer obj c3492688! [ 521.080000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x94/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.080000] RTMP_AllTimerListRelease: Cancel timer obj c3496fc0! [ 521.080000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x7c/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.080000] RTMP_AllTimerListRelease: Cancel timer obj c3496ff4! [ 521.080000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x94/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.080000] RTMP_AllTimerListRelease: Cancel timer obj c349b92c! [ 521.080000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x7c/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.080000] RTMP_AllTimerListRelease: Cancel timer obj c349b960! [ 521.080000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x94/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.080000] RTMP_AllTimerListRelease: Cancel timer obj c34a0298! [ 521.080000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x7c/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.080000] RTMP_AllTimerListRelease: Cancel timer obj c34a02cc! [ 521.080000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x94/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.080000] RTMP_AllTimerListRelease: Cancel timer obj c34a4c04! [ 521.080000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x7c/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.080000] RTMP_AllTimerListRelease: Cancel timer obj c34a4c38! [ 521.080000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x94/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.080000] RTMP_AllTimerListRelease: Cancel timer obj c34a9570! [ 521.080000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x7c/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.080000] RTMP_AllTimerListRelease: Cancel timer obj c34a95a4! [ 521.080000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x94/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.080000] RTMP_AllTimerListRelease: Cancel timer obj c34adedc! [ 521.084000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x7c/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.084000] RTMP_AllTimerListRelease: Cancel timer obj c34adf10! [ 521.084000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x94/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.084000] RTMP_AllTimerListRelease: Cancel timer obj c34b2848! [ 521.084000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x7c/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.084000] RTMP_AllTimerListRelease: Cancel timer obj c34b287c! [ 521.084000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x94/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.084000] RTMP_AllTimerListRelease: Cancel timer obj c34b71b4! [ 521.084000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x7c/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.084000] RTMP_AllTimerListRelease: Cancel timer obj c34b71e8! [ 521.084000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x94/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.084000] RTMP_AllTimerListRelease: Cancel timer obj c34bbb20! [ 521.084000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x7c/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.084000] RTMP_AllTimerListRelease: Cancel timer obj c34bbb54! [ 521.084000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x94/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.084000] RTMP_AllTimerListRelease: Cancel timer obj c34c048c! [ 521.084000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x7c/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.084000] RTMP_AllTimerListRelease: Cancel timer obj c34c04c0! [ 521.084000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x94/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.084000] RTMP_AllTimerListRelease: Cancel timer obj c34c4df8! [ 521.084000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x7c/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.084000] RTMP_AllTimerListRelease: Cancel timer obj c34c4e2c! [ 521.084000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x94/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.084000] RTMP_AllTimerListRelease: Cancel timer obj c34c9764! [ 521.084000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x7c/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.084000] RTMP_AllTimerListRelease: Cancel timer obj c34c9798! [ 521.084000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x94/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.084000] RTMP_AllTimerListRelease: Cancel timer obj c34ce0d0! [ 521.088000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x7c/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.088000] RTMP_AllTimerListRelease: Cancel timer obj c34ce104! [ 521.088000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x94/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.088000] RTMP_AllTimerListRelease: Cancel timer obj c34d2a3c! [ 521.088000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x7c/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.088000] RTMP_AllTimerListRelease: Cancel timer obj c34d2a70! [ 521.088000] RTMP_AllTimerListRelease: Timer is allocated by RRM_CfgInit+0x94/0x168 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.088000] RTMP_AllTimerListRelease: Cancel timer obj c37eb540! [ 521.088000] RTMP_AllTimerListRelease: Timer is allocated by RedInit+0x114/0x210 [mt7663e],Valid:1,Lock:c37ebd4c,State:0 [ 521.088000] fw_own(): Write 1 to MT_CONN_HIF_ON_LPCTL bit 0 to set FW own [ 522.604000] <---HwCtrlThread [ 522.612000] EXIT REDUCE TCP ACK, rai0 procd: - reboot [ 522.800000] Stopped WatchDog Timer. - [ 522.812000] Restarting system. U-Boot 1.1.3 (Jun 3 2019 - 10:14:35) Board: Ralink APSoC DRAM: 128 MB relocate_code Pointer at: 87f98000 Config XHCI 40M PLL ****************************** Software System Reset Occurred ****************************** Allocate 16 byte aligned buffer: 87fcb030 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C2 F1 80 95 02] Device found in MTK table, ID: c2f1, EXT_ID: 809502 Support this Device in MTK table! c2f1 select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 1023 load fact bbt success [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 ....============================================ Ralink UBoot Version: 5.0.0.0 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: NAND Flash Date:Jun 3 2019 Time:10:14:35 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =128 Mbytes #Reset_MT7530 set LAN/WAN WLLLL .## Starting application at 0x81E00000 ... Z-LOADER V1.29 | 06/03/2019 10:14:38 ... Checking image 2... Image Name: 3.10(XIQ.0)b20 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 6119705 Bytes = 5.8 MB Load Address: 80001000 Entry Point: 80001000 .............................................................................................. Verifying Combo Checksum ... ..............................................................................................## Booting image at bf700000 ... Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80001000) ... ## Giving linux memsize in MB, 128 Starting kernel ... OpenWrt kernel loader for MIPS based SoC Copyright (C) 2011 Gabor Juhos Decompressing kernel... done! Starting kernel at 80001000... [ 0.000000] Linux version 5.4.92 ([email protected]) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r0+15625-24d5ef8757)) #0 SMP Thu Jan 28 04:11:26 2021 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is I-O DATA WN-DX1200GR [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] percpu: Embedded 14 pages/cpu s26736 r8192 d22416 u57344 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Writing ErrCtl register=00030800 [ 0.000000] Readback ErrCtl register=00030800 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 117260K/131072K available (5799K kernel code, 201K rwdata, 1244K rodata, 4776K init, 230K bss, 13812K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from start_kernel+0x340/0x558 with crng_init=0 [ 0.000000] CPU Clock: 880MHz [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns [ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns [ 0.015478] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360) [ 0.055830] pid_max: default: 32768 minimum: 301 [ 0.065177] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.079584] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.097681] rcu: Hierarchical SRCU implementation. [ 0.107786] smp: Bringing up secondary CPUs ... [ 0.143182] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.143192] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.143204] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.143306] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.144962] Synchronize counters for CPU 1: done. [ 0.234245] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.234253] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.234261] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.234324] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.243495] Synchronize counters for CPU 2: done. [ 0.329468] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.329476] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.329484] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.329548] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.331096] Synchronize counters for CPU 3: done. [ 0.390706] smp: Brought up 1 node, 4 CPUs [ 0.403220] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.422512] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.436337] pinctrl core: initialized pinctrl subsystem [ 0.448099] NET: Registered protocol family 16 [ 0.482706] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 [ 0.503332] clocksource: Switched to clocksource GIC [ 0.515000] NET: Registered protocol family 2 [ 0.524218] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.540739] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.555924] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.569914] TCP: Hash tables configured (established 1024 bind 1024) [ 0.582651] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.595540] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.609599] NET: Registered protocol family 1 [ 0.618155] PCI: CLS 0 bytes, default 32 [ 4.735306] 4 CPUs re-calibrate udelay(lpj = 1163264) [ 4.746757] random: fast init done [ 4.753511] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 4.777917] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 4.789405] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 4.811827] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 4.823097] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 4.834391] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 4.846103] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 4.859965] printk: console [ttyS0] disabled [ 4.868406] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A [ 4.886337] printk: console [ttyS0] enabled [ 4.886337] printk: console [ttyS0] enabled [ 4.902890] printk: bootconsole [early0] disabled [ 4.902890] printk: bootconsole [early0] disabled [ 4.923748] mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388 [ 4.938566] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1 [ 4.951222] nand: Macronix MX30LF1G189C [ 4.958863] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 4.973945] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits [ 4.986984] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134 [ 5.001564] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134 [ 5.016126] nand: timing mode 1 not acknowledged by the NAND chip [ 5.028267] mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388 [ 5.042834] Scanning device for bad blocks [ 6.350379] 11 fixed-partitions partitions found on MTD device mt7621-nand [ 6.364077] Creating 11 MTD partitions on "mt7621-nand": [ 6.374664] 0x000000000000-0x000000100000 : "u-boot" [ 6.385837] 0x000000100000-0x000000200000 : "u-boot-env" [ 6.397703] 0x000000200000-0x000000400000 : "factory" [ 6.409048] 0x000000400000-0x000000800000 : "kernel" [ 6.420142] 0x000000800000-0x000003600000 : "ubi" [ 6.430876] 0x000003600000-0x000003700000 : "Config" [ 6.441882] 0x000003700000-0x000006900000 : "firmware_2" [ 6.453837] 0x000006900000-0x000006a00000 : "Config_2" [ 6.465195] 0x000006a00000-0x000006b00000 : "persist" [ 6.476418] 0x000006b00000-0x000006c00000 : "idmkey" [ 6.487626] 0x000006c00000-0x000007f80000 : "Backup" [ 6.500132] libphy: Fixed MDIO Bus: probed [ 6.533706] libphy: mdio: probed [ 6.540399] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 6.556801] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 20 [ 6.575490] mt7621-pci 1e140000.pcie: Parsing DT failed [ 6.588446] NET: Registered protocol family 10 [ 6.598680] Segment Routing with IPv6 [ 6.606106] NET: Registered protocol family 17 [ 6.615370] 8021q: 802.1Q VLAN Support v1.8 [ 6.625672] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 6.713159] libphy: dsa slave smi: probed [ 6.721607] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY] [ 6.739473] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY] [ 6.757392] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY] [ 6.775360] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY] [ 6.793255] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY] [ 6.811402] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode [ 6.829022] DSA: tree 0 setup [ 6.835303] rt2880-pinmux pinctrl: pcie is already enabled [ 6.846244] mt7621-pci 1e140000.pcie: Error applying setting, reverse things back [ 6.861300] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1) [ 6.876220] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0) [ 6.990736] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz [ 7.001853] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz [ 7.112667] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK) [ 7.126534] mt7621-pci 1e140000.pcie: PCIE0 enabled [ 7.136254] mt7621-pci 1e140000.pcie: PCIE1 enabled [ 7.145974] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 7.164695] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00 [ 7.177372] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 7.191067] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 7.204765] pci_bus 0000:00: root bus resource [bus 00-ff] [ 7.215735] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 7.227739] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 7.240231] pci 0000:00:00.0: reg 0x14: [mem 0x60300000-0x6030ffff] [ 7.252781] pci 0000:00:00.0: supports D1 [ 7.260765] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 7.272618] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400 [ 7.284622] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 7.297114] pci 0000:00:01.0: reg 0x14: [mem 0x60310000-0x6031ffff] [ 7.309654] pci 0000:00:01.0: supports D1 [ 7.317638] pci 0000:00:01.0: PME# supported from D0 D1 D3hot [ 7.330602] pci 0000:01:00.0: [14c3:7603] type 00 class 0x028000 [ 7.342630] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff] [ 7.355252] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 7.368711] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 7.379137] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 7.391293] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 7.404824] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 7.418231] pci 0000:02:00.0: [14c3:7663] type 00 class 0x000280 [ 7.430259] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref] [ 7.444663] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref] [ 7.459066] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref] [ 7.473569] pci 0000:02:00.0: supports D1 D2 [ 7.482074] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 7.495313] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 7.524152] pci 0000:00:01.0: PCI bridge to [bus 02-ff] [ 7.534569] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff] [ 7.546714] pci 0000:00:01.0: bridge window [mem 0x60100000-0x602fffff pref] [ 7.561109] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 7.574331] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 7.587508] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 7.601380] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] [ 7.614552] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] [ 7.628430] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 7.641957] pci 0000:00:01.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref] [ 7.656351] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff] [ 7.669879] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff] [ 7.683407] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff] [ 7.696933] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff] [ 7.710461] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff] [ 7.723989] pci 0000:00:00.0: PCI bridge to [bus 01] [ 7.733877] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff] [ 7.747405] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 7.760946] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit pref] [ 7.776388] pci 0000:02:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bit pref] [ 7.791832] pci 0000:02:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bit pref] [ 7.807265] pci 0000:00:01.0: PCI bridge to [bus 02] [ 7.817172] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff] [ 7.830692] pci 0000:00:01.0: bridge window [mem 0x60100000-0x602fffff pref] [ 7.846462] UBI error: no valid UBI magic found inside mtd4 [ 7.857650] hctosys: unable to open rtc device (rtc0) [ 7.868406] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off [ 7.888098] Freeing unused kernel memory: 4776K [ 7.897143] This architecture does not have kernel memory protection. [ 7.909963] Run /init as init process [ 8.252153] init: Console is alive [ 8.259170] init: - watchdog - [ 8.276690] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 8.295229] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 8.315660] init: - preinit - [ 8.455237] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 8.471363] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 8.488228] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 8.557171] random: jshn: uninitialized urandom read (4 bytes read) [ 8.625601] random: jshn: uninitialized urandom read (4 bytes read) [ 8.668872] random: jshn: uninitialized urandom read (4 bytes read) [ 8.884506] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 8.898103] 8021q: adding VLAN 0 to HW filter on device lan1 Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 13.049917] procd: - early - [ 13.055780] procd: - watchdog - [ 13.599459] procd: - watchdog - [ 13.606158] procd: - ubus - [ 13.665165] procd: - init - Please press Enter to activate this console. [ 13.984949] kmodloader: loading kernel modules from /etc/modules.d/* [ 14.051077] Loading modules backported from Linux version v5.8.18-0-gab435ce49bd1 [ 14.066031] Backport generated by backports.git v5.8.18-1-0-ga630fd46 [ 14.126328] xt_time: kernel timezone is -0000 [ 14.136863] urngd: v1.0.2 started. [ 14.178248] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=22 [ 14.189062] pci 0000:00:00.0: enabling device (0006 -> 0007) [ 14.200345] mt7603e 0000:01:00.0: enabling device (0000 -> 0002) [ 14.212506] mt7603e 0000:01:00.0: ASIC revision: 76030010 [ 14.283230] random: crng init done [ 14.290030] random: 7 urandom warning(s) missed due to ratelimiting [ 14.840222] mt7603e 0000:01:00.0: Firmware Version: ap_pcie [ 14.851378] mt7603e 0000:01:00.0: Build Time: 20160107100755 [ 14.887314] mt7603e 0000:01:00.0: firmware init done [ 15.074355] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=23 [ 15.085288] pci 0000:00:01.0: enabling device (0006 -> 0007) [ 15.096607] mt7615e 0000:02:00.0: enabling device (0000 -> 0002) [ 15.118995] mt7615e 0000:02:00.0: use otp data only for mt7615e driver [ 15.132084] mt7615e 0000:02:00.0: Invalid MAC address, using random address a2:dd:39:cd:5d:66 [ 15.175527] PPP generic driver version 2.4.2 [ 15.185576] NET: Registered protocol family 24 [ 15.234938] kmodloader: done loading kernel modules from /etc/modules.d/* [ 15.776744] mt7615e 0000:02:00.0: mediatek/mt7663pr2h.bin not found, switching to mediatek/mt7663pr2h_rebb.bin [ 15.798851] mt7615e 0000:02:00.0: HW/SW Version: 0x65322d31, Build Time: 19091404338b809 [ 15.798851] [ 15.824921] mt7615e 0000:02:00.0: N9 Firmware Version: 7663mp1827, Build Time: 20190914043434 [ 15.841994] mt7615e 0000:02:00.0: Region number: 0x3 [ 15.851966] mt7615e 0000:02:00.0: Parsing tailer Region: 0 [ 15.865675] mt7615e 0000:02:00.0: Region 0, override_addr = 0x00112c00 [ 15.878732] mt7615e 0000:02:00.0: Parsing tailer Region: 1 [ 15.890485] mt7615e 0000:02:00.0: Parsing tailer Region: 2 [ 15.901832] mt7615e 0000:02:00.0: override_addr = 0x00112c00, option = 3 [ 27.520336] mtk_soc_eth 1e100000.ethernet eth0: Link is Down [ 27.532762] mtk_soc_eth 1e100000.ethernet: PPE table busy [ 27.552221] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 27.568198] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 27.570704] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 27.598845] 8021q: adding VLAN 0 to HW filter on device lan1 [ 27.613457] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 27.627005] br-lan: port 1(lan1) entered blocking state [ 27.637547] br-lan: port 1(lan1) entered disabled state [ 27.648700] device lan1 entered promiscuous mode [ 27.657948] device eth0 entered promiscuous mode [ 27.686636] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode [ 27.700698] 8021q: adding VLAN 0 to HW filter on device lan2 [ 27.715262] br-lan: port 2(lan2) entered blocking state [ 27.725865] br-lan: port 2(lan2) entered disabled state [ 27.737539] device lan2 entered promiscuous mode [ 27.758013] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode [ 27.771828] 8021q: adding VLAN 0 to HW filter on device lan3 [ 27.787162] br-lan: port 3(lan3) entered blocking state [ 27.797700] br-lan: port 3(lan3) entered disabled state [ 27.809564] device lan3 entered promiscuous mode [ 27.828601] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode [ 27.842391] 8021q: adding VLAN 0 to HW filter on device lan4 [ 27.856955] br-lan: port 4(lan4) entered blocking state [ 27.867413] br-lan: port 4(lan4) entered disabled state [ 27.879478] device lan4 entered promiscuous mode [ 27.904540] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode [ 27.918357] 8021q: adding VLAN 0 to HW filter on device wan [ 31.815811] mt7530 mdio-bus:1f lan2: Link is Up - 1Gbps/Full - flow control off [ 31.830439] br-lan: port 2(lan2) entered blocking state [ 31.840899] br-lan: port 2(lan2) entered forwarding state [ 31.852507] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 32.007823] mt7530 mdio-bus:1f wan: Link is Up - 1Gbps/Full - flow control off [ 32.022269] IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready BusyBox v1.31.1 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r0+15639-63ba99c5ea ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:/# cd /tmp root@OpenWrt:/tmp# wget https://taiha.net/jenkins/job/OpenWrt-master-IODATA-WN-D X1200GR/lastSuccessfulBuild/artifact/bin/targets/ramips/mt7621/openwrt-ramips-mt 7621-iodata_wn-dx1200gr-squashfs-sysupgrade.bin Downloading 'https://taiha.net/jenkins/job/OpenWrt-master-IODATA-WN-DX1200GR/lastSuccessfulBuild/artifact/bin/targets/ramips/mt7621/openwrt-ramips-mt7621-iodata_wn-dx1200gr-squashfs-sysupgrade.bin' Connecting to 240b:12:500:65f0::88a:443 Writing to 'openwrt-ramips-mt7621-iodata_wn-dx1200gr-squashfs-sysupgrade.bin' openwrt-ramips-mt762 100% |*******************************| 6001k 0:00:00 ETA Download completed (6145094 bytes) root@OpenWrt:/tmp# sysupgrade openwrt-ramips-mt7621-iodata_wn-dx1200gr-squashfs- sysupgrade.bin Cannot save config while running from ramdisk. Thu Jan 28 09:59:27 UTC 2021 upgrade: Commencing upgrade. Closing all shell sessions. Watchdog handover: fd=3 - watchdog - killall: telnetd: no process killed Thu Jan 28 09:59:28 UTC 2021 upgrade: Sending TERM to remaining processes ... logd hostapd wpa_supplicant netifd odhcpd ntpd dnsmasq ubusd urngdsh: S: out of range sh: S: out of range Thu Jan 28 09:59:31 UTC 2021 upgrade: Sending KILL to remaining processes ...sh: S: out of range sh: S: out of range [ 85.147735] sh (2713): drop_caches: 3 Thu Jan 28 09:59:32 UTC 2021 upgrade: Switching to ramdisk... Thu Jan 28 09:59:34 UTC 2021 upgrade: Performing system upgrade... current: bootnum => 2, debugflag => 0 ### switch to 1st os-image on next boot ### ### enable debug ### Unlocking kernel ... Writing from to kernel ... [ 89.118408] ubi0: attaching mtd4 [ 89.388823] ubi0: scanning is finished [ 89.396341] ubi0 error: ubi_read_volume_table: the layout volume was not found [ 89.410858] ubi0 error: ubi_attach_mtd_dev: failed to attach mtd4, error -22 ubiattach: error!: cannot attach mtd4 error 22 (Invalid argument) ubiformat: mtd4 (nand), size 48234496 bytes (46.0 MiB), 368 eraseblocks of 131072 bytes (128.0 KiB), min. I/O size 2048 bytes libscan: scanning eraseblock 367 -- 100 % complete ubiformat: 324 eraseblocks are supposedly empty ubiformat: warning!: 44 of 368 eraseblocks contain non-UBI data ubiformat: warning!: only 0 of 368 eraseblocks have valid erase counter ubiformat: erase counter 0 will be used for all eraseblocks ubiformat: note, arbitrary erase counter value may be specified using -e option ubiformat: use erase counter 0 for all eraseblocks ubiformat: formatting eraseb[ 96.174691] ubi0: attaching mtd4 ubiformat: formatting eraseblock 367 -- 100 % complete [ 96.653821] ubi0: scanning is finished [ 96.677449] ubi0: attached mtd4 (name "ubi", size 46 MiB) [ 96.688262] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 96.701959] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 96.715484] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 96.729351] ubi0: good PEBs: 368, bad PEBs: 0, corrupted PEBs: 0 [ 96.741318] ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128 [ 96.755785] ubi0: max/mean erase counter: 0/0, WL threshold: 4096, image sequence number: 700913185 [ 96.773857] ubi0: available PEBs: 344, total reserved PEBs: 24, PEBs reserved for bad PEB handling: 20 [ 96.792435] ubi0: background thread "ubi_bgt0d" started, PID 3326 UBI device number 0, total 368 LEBs (46727168 bytes, 44.5 MiB), available 344 LEBs (43679744 bytes, 41.6 MiB), LEB size 126976 bytes (124.0 KiB) Volume ID 0, size 30 LEBs (3809280 bytes, 3.6 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs", alignment 1 Set volume size to 39870464 Volume ID 1, size 314 LEBs (39870464 bytes, 38.0 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs_data", alignment 1 sysupgrade successful umount: can't unmount /dev: Resource busy umount: can't unmount /tmp: Resource busy [ 98.719748] reboot: Restarting system U-Boot 1.1.3 (Jun 3 2019 - 10:14:35) Board: Ralink APSoC DRAM: 128 MB relocate_code Pointer at: 87f98000 Config XHCI 40M PLL ****************************** Software System Reset Occurred ****************************** Allocate 16 byte aligned buffer: 87fcb030 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C2 F1 80 95 02] Device found in MTK table, ID: c2f1, EXT_ID: 809502 Support this Device in MTK table! c2f1 select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 1023 load fact bbt success [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 ....============================================ Ralink UBoot Version: 5.0.0.0 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: NAND Flash Date:Jun 3 2019 Time:10:14:35 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =128 Mbytes #Reset_MT7530 set LAN/WAN WLLLL .## Starting application at 0x81E00000 ... Z-LOADER V1.29 | 06/03/2019 10:14:38 ...Hit ESC key to stop autoboot: 1 Checking image 1... Image Name: MIPS OpenWrt Linux-5.4.9 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 2435168 Bytes = 2.3 MB Load Address: 80001000 Entry Point: 80001000 ...................................... Verifying Checksum ... ## Booting image at bc400000 ... Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80001000) ... ## Giving linux memsize in MB, 128 Starting kernel ... OpenWrt kernel loader for MIPS based SoC Copyright (C) 2011 Gabor Juhos Decompressing kernel... done! Starting kernel at 80001000... [ 0.000000] Linux version 5.4.92 ([email protected]) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r0+15625-24d5ef8757)) #0 SMP Thu Jan 28 04:11:26 2021 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is I-O DATA WN-DX1200GR [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] percpu: Embedded 14 pages/cpu s26736 r8192 d22416 u57344 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Writing ErrCtl register=00030800 [ 0.000000] Readback ErrCtl register=00030800 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 120780K/131072K available (5799K kernel code, 205K rwdata, 1240K rodata, 1256K init, 230K bss, 10292K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from start_kernel+0x340/0x558 with crng_init=0 [ 0.000000] CPU Clock: 880MHz [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns [ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns [ 0.015477] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360) [ 0.055830] pid_max: default: 32768 minimum: 301 [ 0.065178] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.079584] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.097687] rcu: Hierarchical SRCU implementation. [ 0.107791] smp: Bringing up secondary CPUs ... [ 4.462762] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 4.462772] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 4.462784] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 4.462884] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.144965] Synchronize counters for CPU 1: done. [ 4.553785] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 4.553794] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 4.553801] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 4.553866] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.239409] Synchronize counters for CPU 2: done. [ 4.644923] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 4.644931] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 4.644939] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 4.645003] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.327008] Synchronize counters for CPU 3: done. [ 0.386613] smp: Brought up 1 node, 4 CPUs [ 0.399159] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.418451] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.432274] pinctrl core: initialized pinctrl subsystem [ 0.444083] NET: Registered protocol family 16 [ 0.478436] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 [ 0.499135] clocksource: Switched to clocksource GIC [ 0.510855] NET: Registered protocol family 2 [ 0.520085] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.536617] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.551795] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.565786] TCP: Hash tables configured (established 1024 bind 1024) [ 0.578521] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.591416] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.605475] NET: Registered protocol family 1 [ 0.614041] PCI: CLS 0 bytes, default 32 [ 0.711096] 4 CPUs re-calibrate udelay(lpj = 1167360) [ 0.722648] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.745927] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.757432] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.779586] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.790863] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.802113] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.813425] random: fast init done [ 0.817706] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 0.833858] printk: console [ttyS0] disabled [ 0.842314] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A [ 0.860242] printk: console [ttyS0] enabled [ 0.860242] printk: console [ttyS0] enabled [ 0.876788] printk: bootconsole [early0] disabled [ 0.876788] printk: bootconsole [early0] disabled [ 0.897578] mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388 [ 0.912423] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1 [ 0.925077] nand: Macronix MX30LF1G189C [ 0.932717] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.947801] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits [ 0.960838] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134 [ 0.975424] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134 [ 0.989987] nand: timing mode 1 not acknowledged by the NAND chip [ 1.002128] mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388 [ 1.016695] Scanning device for bad blocks [ 2.321604] 11 fixed-partitions partitions found on MTD device mt7621-nand [ 2.335302] Creating 11 MTD partitions on "mt7621-nand": [ 2.345887] 0x000000000000-0x000000100000 : "u-boot" [ 2.356920] 0x000000100000-0x000000200000 : "u-boot-env" [ 2.368570] 0x000000200000-0x000000400000 : "factory" [ 2.379812] 0x000000400000-0x000000800000 : "kernel" [ 2.390796] 0x000000800000-0x000003600000 : "ubi" [ 2.401519] 0x000003600000-0x000003700000 : "Config" [ 2.412518] 0x000003700000-0x000006900000 : "firmware_2" [ 2.424476] 0x000006900000-0x000006a00000 : "Config_2" [ 2.435906] 0x000006a00000-0x000006b00000 : "persist" [ 2.447162] 0x000006b00000-0x000006c00000 : "idmkey" [ 2.458215] 0x000006c00000-0x000007f80000 : "Backup" [ 2.470431] libphy: Fixed MDIO Bus: probed [ 2.505521] libphy: mdio: probed [ 2.512184] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 2.528382] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 20 [ 2.547152] mt7621-pci 1e140000.pcie: Parsing DT failed [ 2.559996] NET: Registered protocol family 10 [ 2.570261] Segment Routing with IPv6 [ 2.577708] NET: Registered protocol family 17 [ 2.586881] 8021q: 802.1Q VLAN Support v1.8 [ 2.597142] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 2.619011] libphy: dsa slave smi: probed [ 2.627483] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY] [ 2.645223] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY] [ 2.663164] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY] [ 2.681079] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY] [ 2.698954] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY] [ 2.716971] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode [ 2.734590] DSA: tree 0 setup [ 2.740829] rt2880-pinmux pinctrl: pcie is already enabled [ 2.751780] mt7621-pci 1e140000.pcie: Error applying setting, reverse things back [ 2.766825] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1) [ 2.781751] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0) [ 2.896581] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz [ 2.907699] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz [ 3.018814] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK) [ 3.032687] mt7621-pci 1e140000.pcie: PCIE0 enabled [ 3.042401] mt7621-pci 1e140000.pcie: PCIE1 enabled [ 3.052127] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 3.070825] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00 [ 3.083500] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 3.097197] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 3.110900] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.121868] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 3.133868] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 3.146360] pci 0000:00:00.0: reg 0x14: [mem 0x60300000-0x6030ffff] [ 3.158914] pci 0000:00:00.0: supports D1 [ 3.166904] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 3.178709] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400 [ 3.190719] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 3.203215] pci 0000:00:01.0: reg 0x14: [mem 0x60310000-0x6031ffff] [ 3.215762] pci 0000:00:01.0: supports D1 [ 3.223749] pci 0000:00:01.0: PME# supported from D0 D1 D3hot [ 3.236610] pci 0000:01:00.0: [14c3:7603] type 00 class 0x028000 [ 3.248640] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff] [ 3.261263] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 3.274650] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 3.285082] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 3.297225] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 3.310756] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.324132] pci 0000:02:00.0: [14c3:7663] type 00 class 0x000280 [ 3.336164] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref] [ 3.350568] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref] [ 3.364980] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref] [ 3.379483] pci 0000:02:00.0: supports D1 D2 [ 3.387990] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 3.401199] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 3.429972] pci 0000:00:01.0: PCI bridge to [bus 02-ff] [ 3.440409] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff] [ 3.452553] pci 0000:00:01.0: bridge window [mem 0x60100000-0x602fffff pref] [ 3.466944] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 3.480171] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 3.493354] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 3.507228] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] [ 3.520405] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] [ 3.534275] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 3.547806] pci 0000:00:01.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref] [ 3.562195] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff] [ 3.575730] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff] [ 3.589258] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff] [ 3.602784] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff] [ 3.616321] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff] [ 3.629853] pci 0000:00:00.0: PCI bridge to [bus 01] [ 3.639748] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff] [ 3.653272] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 3.666806] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit pref] [ 3.682250] pci 0000:02:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bit pref] [ 3.697696] pci 0000:02:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bit pref] [ 3.713135] pci 0000:00:01.0: PCI bridge to [bus 02] [ 3.723026] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff] [ 3.736554] pci 0000:00:01.0: bridge window [mem 0x60100000-0x602fffff pref] [ 3.751519] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off [ 3.752643] UBI: auto-attach mtd4 [ 3.771907] ubi0: attaching mtd4 [ 4.245806] ubi0: scanning is finished [ 4.269645] ubi0: attached mtd4 (name "ubi", size 46 MiB) [ 4.280422] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 4.294109] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 4.307627] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 4.321486] ubi0: good PEBs: 368, bad PEBs: 0, corrupted PEBs: 0 [ 4.333444] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 4.347828] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 700913185 [ 4.365838] ubi0: available PEBs: 0, total reserved PEBs: 368, PEBs reserved for bad PEB handling: 20 [ 4.384220] ubi0: background thread "ubi_bgt0d" started, PID 464 [ 4.386006] block ubiblock0_0: created from ubi0:0(rootfs) [ 4.407128] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 4.420996] hctosys: unable to open rtc device (rtc0) [ 4.437555] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 4.455983] Freeing unused kernel memory: 1256K [ 4.465029] This architecture does not have kernel memory protection. [ 4.477851] Run /sbin/init as init process [ 5.015463] init: Console is alive [ 5.022488] init: - watchdog - [ 5.651755] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 5.747644] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 5.771435] init: - preinit - [ 6.415784] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 6.431845] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 6.448697] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.577430] random: jshn: uninitialized urandom read (4 bytes read) [ 6.645474] random: jshn: uninitialized urandom read (4 bytes read) [ 6.687961] random: jshn: uninitialized urandom read (4 bytes read) [ 6.900879] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 6.914485] 8021q: adding VLAN 0 to HW filter on device lan1 Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 11.097808] UBIFS (ubi0:1): default file-system created [ 11.109641] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 11.121183] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 578 [ 11.246043] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 11.261718] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 11.281482] UBIFS (ubi0:1): FS size: 38600704 bytes (36 MiB, 304 LEBs), journal size 1904640 bytes (1 MiB, 15 LEBs) [ 11.302273] UBIFS (ubi0:1): reserved for root: 1823206 bytes (1780 KiB) [ 11.315460] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 4EC6A2FB-37FD-4826-B555-FFC3EE7DE706, small LPT model [ 11.341101] mount_root: overlay filesystem has not been fully initialized yet [ 11.355729] mount_root: switching to ubifs overlay [ 11.371981] urandom-seed: Seed file not found (/etc/urandom.seed) [ 11.519013] procd: - early - [ 11.524903] procd: - watchdog - [ 12.115261] procd: - watchdog - [ 12.122182] procd: - ubus - [ 12.181128] procd: - init - Please press Enter to activate this console. [ 12.637331] kmodloader: loading kernel modules from /etc/modules.d/* [ 12.704497] Loading modules backported from Linux version v5.8.18-0-gab435ce49bd1 [ 12.719478] Backport generated by backports.git v5.8.18-1-0-ga630fd46 [ 12.793037] xt_time: kernel timezone is -0000 [ 12.849779] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=22 [ 12.860610] pci 0000:00:00.0: enabling device (0006 -> 0007) [ 12.871912] mt7603e 0000:01:00.0: enabling device (0000 -> 0002) [ 12.884136] mt7603e 0000:01:00.0: ASIC revision: 76030010 [ 12.918654] urngd: v1.0.2 started. [ 13.062879] random: crng init done [ 13.069674] random: 7 urandom warning(s) missed due to ratelimiting [ 13.512377] mt7603e 0000:01:00.0: Firmware Version: ap_pcie [ 13.523508] mt7603e 0000:01:00.0: Build Time: 20160107100755 [ 13.559119] mt7603e 0000:01:00.0: firmware init done [ 13.745565] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=23 [ 13.756371] pci 0000:00:01.0: enabling device (0006 -> 0007) [ 13.767671] mt7615e 0000:02:00.0: enabling device (0000 -> 0002) [ 13.788158] mt7615e 0000:02:00.0: use otp data only for mt7615e driver [ 13.801310] mt7615e 0000:02:00.0: Invalid MAC address, using random address 2a:c1:a4:a3:78:c1 [ 13.850508] PPP generic driver version 2.4.2 [ 13.861052] NET: Registered protocol family 24 [ 13.958474] kmodloader: done loading kernel modules from /etc/modules.d/* [ 14.758144] mt7615e 0000:02:00.0: mediatek/mt7663pr2h.bin not found, switching to mediatek/mt7663pr2h_rebb.bin [ 14.888011] mt7615e 0000:02:00.0: HW/SW Version: 0x65322d31, Build Time: 19091404338b809 [ 14.888011] [ 15.050594] mt7615e 0000:02:00.0: N9 Firmware Version: 7663mp1827, Build Time: 20190914043434 [ 15.067660] mt7615e 0000:02:00.0: Region number: 0x3 [ 15.077605] mt7615e 0000:02:00.0: Parsing tailer Region: 0 [ 15.091405] mt7615e 0000:02:00.0: Region 0, override_addr = 0x00112c00 [ 15.104443] mt7615e 0000:02:00.0: Parsing tailer Region: 1 [ 15.116186] mt7615e 0000:02:00.0: Parsing tailer Region: 2 [ 15.127515] mt7615e 0000:02:00.0: override_addr = 0x00112c00, option = 3 [ 39.105441] mtk_soc_eth 1e100000.ethernet eth0: Link is Down [ 39.117850] mtk_soc_eth 1e100000.ethernet: PPE table busy [ 39.136917] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 39.152985] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 39.156569] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 39.183609] 8021q: adding VLAN 0 to HW filter on device lan1 [ 39.197985] br-lan: port 1(lan1) entered blocking state [ 39.208586] br-lan: port 1(lan1) entered disabled state [ 39.220079] device lan1 entered promiscuous mode [ 39.229333] device eth0 entered promiscuous mode [ 39.243786] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 39.269584] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode [ 39.283873] 8021q: adding VLAN 0 to HW filter on device lan2 [ 39.298674] br-lan: port 2(lan2) entered blocking state [ 39.309287] br-lan: port 2(lan2) entered disabled state [ 39.321319] device lan2 entered promiscuous mode [ 39.341318] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode [ 39.355149] 8021q: adding VLAN 0 to HW filter on device lan3 [ 39.369855] br-lan: port 3(lan3) entered blocking state [ 39.380406] br-lan: port 3(lan3) entered disabled state [ 39.392342] device lan3 entered promiscuous mode [ 39.412350] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode [ 39.426509] 8021q: adding VLAN 0 to HW filter on device lan4 [ 39.441121] br-lan: port 4(lan4) entered blocking state [ 39.451619] br-lan: port 4(lan4) entered disabled state [ 39.463838] device lan4 entered promiscuous mode [ 39.487168] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode [ 39.500771] 8021q: adding VLAN 0 to HW filter on device wan [ 43.383621] mt7530 mdio-bus:1f lan2: Link is Up - 1Gbps/Full - flow control off [ 43.398249] br-lan: port 2(lan2) entered blocking state [ 43.408707] br-lan: port 2(lan2) entered forwarding state [ 43.420427] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 43.609505] mt7530 mdio-bus:1f wan: Link is Up - 1Gbps/Full - flow control off [ 43.623980] IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready [ 58.743391] mt7530 mdio-bus:1f lan2: Link is Down [ 58.752899] br-lan: port 2(lan2) entered disabled state BusyBox v1.31.1 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r0+15639-63ba99c5ea ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:/#
大破雑記帳 