BootROM 1.20
Booting from SPI flash
MARU_DEBUG_RESET
High speed PHY - Ver 1.6.0 (COM-PHY-V20)
Read Reg: 0x00020868= 01022200
Write Reg: 0x00020868= 01022000
Step 1: First phase of PEX-PIPE Configuration
Write Reg: 0x00041B00= 00C10025
Write Reg: 0x00041B00= 00C20200
Write Reg: 0x00041B00= 00C5011F
Write Reg: 0x00081B00= 00C10025
Write Reg: 0x00081B00= 00C3000F
Write Reg: 0x00081B00= 00C5011F
Step 2: Configure the desire PIN_PHY_GEN
Read Reg: 0x000A4058= 00000227
Write Reg: 0x000A4058= 00000220
Read Reg: 0x000A2058= 00000227
Write Reg: 0x000A2058= 00000220
Step 3 QSGMII enable
Step 4: Configure SERDES MUXes
Write Reg: 0x00018270= 02211111
Write Reg: 0x00018274= 00000000
Step 5: Activate the RX High Impedance Mode
Write Reg: 0x00041B00= 00481084
Write Reg: 0x00081B00= 00489084
Write Reg: 0x000A4920= 00008084
Write Reg: 0x000A2920= 00008084
Step 6: [PEX-Only] PEX-Main configuration (X4 or X1)
Write Reg: 0x00018204= 00000200
Read Reg: 0x00018204= 00000200
Write Reg: 0x00018204= 00000330
Step 6.2: [PEX-Only] PCI Express Link Capabilities
Read Reg: 0x0004006C= 0007AC42
Write Reg: 0x0004006C= 0007AC42
Read Reg: 0x0008006C= 0007AC12
Write Reg: 0x0008006C= 0007AC12
Step 7: [PEX-X4 Only] To create PEX-Link
Read Reg: 0x000182F8= FFFF0000
Write Reg: 0x000182F8= FFFF000F
Steps 7,8,9,10 and 11
Write Reg: 0x00041B00= 0001FC60
Write Reg: 0x00081B00= 0001FC60
Write Reg: 0x000A4804= 0000F801
Write Reg: 0x000A488C= 00000400
Write Reg: 0x000A4918= 00000400
Read Reg: 0x000A4058= 00000220
Write Reg: 0x000A4058= 00000227
Write Reg: 0x000A2804= 0000F801
Write Reg: 0x000A288C= 00000400
Write Reg: 0x000A2918= 00000400
Read Reg: 0x000A2058= 00000220
Write Reg: 0x000A2058= 00000227
Steps 12: [PEX-Only] Last phase of PEX-PIPE ConfigurationWrite Reg: 0x00041B00= 00C10024
Write Reg: 0x00081B00= 00C10024
Steps 13: Wait 15ms before checking resultsRead Reg: 0x000A405C= 00013007
Read Reg: 0x000A205C= 00003007
Steps 14: [PEX-Only] In order to configureRead Reg: 0x00040060= 00420010
Write Reg: 0x00040060= 00420010
Read Reg: 0x00080060= 00420010
Write Reg: 0x00080060= 00420010
Steps 15: [PEX-Only] In order to configureWrite Reg: 0x00041B00= 000F2A21
Write Reg: 0x00041B00= 004F6219
Write Reg: 0x00081B00= 000F2A21
Write Reg: 0x00081B00= 004F6219
Write Reg: 0x000A483C= 00008A31
Write Reg: 0x000A4834= 0000C928
Write Reg: 0x000A4838= 000030F0
Write Reg: 0x000A4840= 000030F5
Write Reg: 0x000A283C= 00008A31
Write Reg: 0x000A2834= 0000C928
Write Reg: 0x000A2838= 000030F0
Write Reg: 0x000A2840= 000030F5
Steps 16: [PEX-Only] Training EnableRead Reg: 0x00018204= 00000330
Write Reg: 0x00018204= 00000333
DDR3 Init. - SPD_SUPPORT: UNDEFINED
DDR3 Init. - defined(MV88F78X60) && !defined(MV88F78X60_Z1) : True
DDR3 Training Sequence - Ver 3.0.0
DDR3 Init. - uiFabOpt : 5
DDR3 Init. - socNum : 00000001
DDR3 Traning Squence - Stage 0
DDR3 Init. - uiCpuFreq : 00000003
DDR3 Init. - ECC_SUPPORT: UNDEFINED
DDR3 Init. - DQS_CLK_ALIGNED: UNDEFINED
DDR3 Traning Squence - Stage 1
DDR3 Training Sequence - Static MC Init
DDR3 Init.[ddr3GetStaticDdrMode()] - chipBoardRev : 5
* DDR3 Init.[ddr3GetStaticDdrMode()] - if chipBoardRev = A0 : 3
* DDR3 Init.[ddr3GetStaticDdrMode()] - if chipBoardRev = B0 : 5
* DDR3 Init.[ddr3GetStaticDdrMode()] - if chipBoardRev = Z1 : 0
DDR3 Init.[ddr3GetStaticDdrMode()] - ddr3GetCpuFreq() : 3
DDR3 Init.[ddr3GetStaticDdrMode()] - ddr3GetFabOpt() : 5
i=0:ddr_modes[i]:cpuFreq[0003] fabFreq[0005] chipBoardRev[0005]
DDR3 Init. - DUNIT_STATIC: DEFINED
DDR3 Init. - AUTO_DETECTION_SUPPORT: UNDEFINED
DDR3 Init. - MV88F78X60: DEFINED
DDR3 Init. - DUNIT_SPD: UNDEFINED
DDR3 Training Sequence - HW Training Procedure
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
Buffalo : Over write the parameter 0x1538 -> 0x00000009
Buffalo : Over write the parameter 0x153C -> 0x0000000f
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
U-Boot 2011.12 (Oct 18 2013 - 04:32:11) Marvell version: 2012_Q4.2
Board: BUFFALO TeraStation =TS3400D=
SoC: MV78230 B0
running 2 CPUs
Custom configuration
CPU: Marvell PJ4B (584) v7 (Rev 2) LE
CPU 0
CPU @ 1333 [MHz]
L2 @ 667 [MHz]
TClock @ 250 [MHz]
DDR @ 667 [MHz]
DDR 32Bit Width, FastPath Memory Access
DDR ECC Disabled
DRAM: 1024 MiB
Map: Code: 0x3fee9000:0x3ff9df78
BSS: 0x3ffef960
Stack: 0x3f9d8ef8
PageTable: 0x003e0000
Heap: 0x3f9d9000:0x3fee9000
NAND: 512 MiB
MMC: MRVL_MMC: 0
SF: Detected MX25L8006E with page size 64 KiB, total 1 MiB
PEX 0.0(0): Root Complex Interface, Detected Link X4, GEN 1.1
PEX 1.0(1): Root Complex Interface, Detected Link X1, GEN 2.0
u-boot envinit tval=fef96294
BOOTVER=0.17
FPU initialized to Run Fast Mode.
USB 0: Host Mode
USB 1: Host Mode
USB 2: Host Mode
sending BOOT_START
Late init
UCOM ID= 0
boardId=4
boot trigger=normal
Marvell Serial ATA Adapter
Integrated Sata device found
Found adapter at bus 0, device 1 ... Scanning channels
MAC Address : 10:6F:3F:xx:xx:8F
boot drive not found.
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
** Bad partition 1 **
** Bad partition 1 **
<>
Wrong Image Format for bootm command
ERROR: can't get kernel image!
device nand0 , # parts = 1
#: name size offset mask_flags
0: nandubifs 0x000020000000 0x000000000000 0
active partition: nand0,0 - (nandubifs) 0x000020000000 @ 0x000000000000
defaults:
mtdids : none
mtdparts: none
Creating 1 MTD partitions on "nand0":
0x000000000000-0x000020000000 : "mtd=0"
Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=0"
UBI: MTD device size: 512 MiB
UBI: number of good PEBs: 4088
UBI: number of bad PEBs: 8
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 4088
UBI: number of PEBs reserved for bad PEB handling: 40
UBI: max/mean erase counter: 1/0
UBIFS: recovery needed
UBIFS: recovery deferred
UBIFS: mounted UBI device 0, volume 0, name "nandubifs"
UBIFS: mounted read-only
UBIFS: file system size: 511586304 bytes (499596 KiB, 487 MiB, 4029 LEBs)
UBIFS: journal size: 25649152 bytes (25048 KiB, 24 MiB, 202 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root: 5182151 bytes (5060 KiB)
Loading file 'uImage.buffalo' to addr 0x01200000 with size 3628464 (0x00375db0)...
Done
Loading file 'initrd.buffalo' to addr 0x02600000 with size 24320911 (0x01731b8f)...
Done
<>
## Booting kernel from Legacy Image at 01200000 ...
Image Name: Linux-3.3.4
Created: 2014-11-10 20:24:08 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3628400 Bytes = 3.5 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02600000 ...
Image Name: initramfs.cpio
Created: 2014-11-10 20:30:14 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 24320847 Bytes = 23.2 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0
Initializing cgroup subsys cpu
Linux version 3.3.4 (jenkins@[email protected]) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC release 201307-2123.0cc69bb4 ) ) #1 SMP Mon Nov 10 14:24:03 CST 2014
CPU: Marvell - PJ4Bv7 Processor [562f5842] revision 2 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
Machine: Marvell Armada XP Development Board
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writealloc
SMP: init cpus
PERCPU: Embedded 7 pages/cpu @c0eee000 s6560 r8192 d13920 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 243839
Kernel command line: console=ttyS0,115200 panic=5 mtdparts=armada-nand:-(nandubifs) ubi.mtd=1 BOOTVER=0.17 UBOOT_DATE=2013/10/18 nandboot=yes earlyprintk
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 959MB = 959MB total
Memory: 943140k/943140k available, 39896k reserved, 114684K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xf5800000 - 0xff000000 ( 152 MB)
lowmem : 0xc0000000 - 0xf5000000 ( 848 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc06b5000 (6836 kB)
.init : 0xc06b5000 - 0xc06eb9a0 ( 219 kB)
.data : 0xc06ec000 - 0xc0726f00 ( 236 kB)
.bss : 0xc0726f24 - 0xc0767838 ( 259 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:211
Initializing ArmadaXP SOC Timer 0
sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms
Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
Initializing cgroup subsys blkio
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
SMP: prepare CPUs (2 cores)
SMP: CPU 0 Waking up CPU 1
Armada-XP Performance Monitor Unit detected (Marvell ID)!!!
hw perfevents: enabled with Armada PJ4 PMU driver, 7 counters available
Setting up static identity map for 0x4efe90 - 0x4efed4
CPU1: Booted secondary processor
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
Brought up 2 CPUs
SMP: Total of 2 processors activated (2664.03 BogoMIPS).
devtmpfs: initialized
xor: measuring software checksum speed
arm4regs : 1087.200 MB/sec
8regs : 957.600 MB/sec
32regs : 1184.000 MB/sec
xor: using function: 32regs (1184.000 MB/sec)
NET: Registered protocol family 16
L0 cache Enabled
Speculative Prefetch Disabled
aurora_l2_init
Aurora: Enabling L2
Support IO coherency.
Marvell Armada-XP BUFFALO TeraStation =TS3400D= Board - Soc: MV88F7823 Rev 2 LE
Detected Tclk 250000000, SysClk 667000000, FabricClk 667000000, PClk 1333000000
LSP version: AXP_2.0.6
gpiochip_add: registered GPIOs 0 to 67 on device: mv_gpio
LCD 0 disabled (0).
registered dev#0 asa ehci_marvell
Marvell USB EHCI Host controller #0: f4827f00
registered dev#1 asa ehci_marvell
Marvell USB EHCI Host controller #1: f48b3000
registered dev#2 asa ehci_marvell
Marvell USB EHCI Host controller #2: f48b3100
PCI-E: Cheking physical bus #0 (controller #0): Enabled - Link UP
PCI-E: Cheking physical bus #1 (controller #4): Enabled - Link UP
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe1ffffff]
PCI: bus0: Fast back to back transfers disabled
PCI host bridge to bus 0000:01
pci_bus 0000:01: root bus resource [mem 0xe8000000-0xe9ffffff]
PCI: bus1: Fast back to back transfers disabled
pci 0000:01:01.0: BAR 0: assigned [mem 0xe8000000-0xe8001fff 64bit]
pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe00fffff 64bit]
pci 0000:00:01.0: BAR 2: can't assign io (size 0x100)
bio: create slab at 0
raid6: int32x1 153 MB/s
raid6: int32x2 235 MB/s
raid6: int32x4 220 MB/s
raid6: int32x8 255 MB/s
raid6: using algorithm int32x8 (255 MB/s)
vgaarb: loaded
SCSI subsystem initialized
Switching to clocksource axp_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 23748K
CESA test started: bufNum = 1, bufSize = 20000
Cesa Test Start: pMbufSrc=f4900000, pFragsSrc=f485c000, pMbufDst=f4900800, pFragsDst=f485e000
mvCesaInit: channels=2, session=32, queue=256
cesadev_init(c06bea24)
Armada XP hwmon thermal sensor initialized.
ArmadaXP Power Managament Suspend Operations Initialized
Initializing Armada-XP CPU power management (WFI)
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON V2 (C) BUFFALO INC. V.2.00 installed.(IRQ=168)
Error : NAK or Illegal Data Recived
Error : NAK or Illegal Data Recived
Error : NAK or Illegal Data Recived
Buffalo Gpio Control Driver (C) BUFFALO INC. Ver.1.00 installed.
Buffalo CPU Inerupts Driver (C) BUFFALO INC. Ver.0.01 alpha1 installed.
initial_polarity_val = 0x00000000
initial_polarity_val_high = 0x0000090f
Buffalo GPIO SATA Hotplug Event Driver (C) BUFFALO INC. Ver.1.00 installed.-Polling mode-
UPSDRV (C) BUFFALO INC. V.1.00 installed.
BUFFALO UPS Recover Function Initialized.
OMRON contact type ups shutdown support enabled!
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
nfs4filelayout_init: NFSv4 File Layout Driver Registering...
Installing knfsd (copyright (C) 1996 [email protected]).
NTFS driver 2.1.30 [Flags: R/O].
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.18)
SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 1664
async_tx: api initialized (async)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Initializing ths8200_init
Initializing dove_adi9889_init
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xd0012000 (irq = 41) is a 16550A
console [ttyS0] enabled
serial8250.3: ttyS1 at MMIO 0xd0012300 (irq = 44) is a 16550A
serial8250.1: ttyS2 at MMIO 0xd0012100 (irq = 42) is a 16550A
serial8250.2: ttyS3 at MMIO 0xd0012200 (irq = 43) is a 16550A
brd: module loaded
loop: module loaded
** BUFFALO Disable Command Queuing Function [sata_mv 0000:00:01.0] **
704211ab 00100146 01000002 00000008
e0000004 00000000 ffffff01 00000000
00000000 00000000 00000000 11ab11ab
00000000 00000040 00000000 0000013a
00025001 00000000 00000000 00000000
00806005 00000000 00000000 00000000
00110010 00000081
sata_mv 0000:00:01.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
scsi0 : sata_mv
scsi1 : sata_mv
scsi2 : sata_mv
scsi3 : sata_mv
ata1: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0022000 irq 58
ata2: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0024000 irq 58
ata3: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0026000 irq 58
ata4: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0028000 irq 58
sata_mv sata_mv.0: cannot get clkdev
** BUFFALO Disable Command Queuing Function [sata_mv sata_mv.0] **
sata_mv sata_mv.0: slots 32 ports 2
scsi4 : sata_mv
scsi5 : sata_mv
ata5: SATA max UDMA/133 irq 55
ata6: SATA max UDMA/133 irq 55
INFO: Found spi_flash 0 - base 0xf0000000, size 0x1000000
INFO: flashInfoFill - Found 1 Flash Devices
INFO: flash_map_init - detected 1 devices
MTD: Initialize the spi_flash device at address 0xf0000000
INFO: Io remapped successfully - phy addr = 0xf0000000, virt addr = 0xfab00000
INFO: Using sflash to probe spi_flash at address 0xf0000000, size 0x1000000, width 2mSPI Serial flash detected @ 0xf0000000, 1024KB (16sec x 64KB)
- detected OK - OK.
armada-nand armada-nand.0: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
1 cmdlinepart partitions found on MTD device armada-nand
Creating 1 MTD partitions on "armada-nand":
0x000000000000-0x000020000000 : "nandubifs"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
ata1: SATA link down (SStatus 0 SControl 300)
ata5: SATA link down (SStatus 0 SControl F300)
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
UBI: max. sequence number: 3359
UBI: attached mtd1 to ubi0
UBI: MTD device name: "nandubifs"
UBI: MTD device size: 512 MiB
UBI: number of good PEBs: 4088
UBI: number of bad PEBs: 8
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 4088
UBI: number of PEBs reserved for bad PEB handling: 40
UBI: max/mean erase counter: 1/0
UBI: image sequence number: 596401107
UBI: background thread "ubi_bgt0d" started, PID 471
mv_eth_probe: port_mask=0xf, cpu_mask=0x3
0 - Base 0x00000000 , Size = 0x40000000.
4 - Base 0xf4000000 , Size = 0x00100000.
8 - Base 0xe0000000 , Size = 0x02000000.
10 - Base 0xe2000000 , Size = 0x02000000.
12 - Base 0xe4000000 , Size = 0x02000000.
14 - Base 0xe6000000 , Size = 0x02000000.
16 - Base 0xe8000000 , Size = 0x02000000.
20 - Base 0xea000000 , Size = 0x02000000.
24 - Base 0xec000000 , Size = 0x02000000.
26 - Base 0xee000000 , Size = 0x02000000.
28 - Base 0xd0000000 , Size = 0x00100000.
30 - Base 0xf0000000 , Size = 0x01000000.
38 - Base 0xfff00000 , Size = 0x00100000.
39 - Base 0xf2000000 , Size = 0x02000000.
41 - Base 0xc8010000 , Size = 0x00010000.
42 - Base 0xf4480000 , Size = 0x00010000.
43 - Base 0xf4500000 , Size = 0x00100000.
o 2 Giga ports supported
o NETA acceleration mode 2
o BM supported for CPU: 4 BM pools
o RX Queue support: 1 Queues * 128 Descriptors
o TX Queue support: 1 Queues * 532 Descriptors
o GSO supported
o GRO supported
o Receive checksum offload supported
o Transmit checksum offload supported
o Driver ERROR statistics enabled
o Loading network interface(s)
o Port 0 is connected to Linux netdevice
link down
giga p=0: mtu=1500, mac=f483be6c
ata4: SATA link down (SStatus 0 SControl 300)
o eth0, ifindex = 2, GbE port = 0
o Port 1 is connected to Linux netdevice
link down
giga p=1: mtu=1500, mac=f483be6c
o eth1, ifindex = 3, GbE port = 1
e1000e: Intel(R) PRO/1000 Network Driver - 1.5.1-k
e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
PPP generic driver version 2.4.2
NET: Registered protocol family 24
i2c /dev entries driver
rtc-rs5c372 0-0032: rs5c372a found, 24hr, driver version 0.6
rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected]
cpuidle: using governor ladder
cpuidle: using governor menu
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
Netfilter messages via NETLINK v0.30.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 5
Registering the dns_resolver key type
VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6
ata6: SATA link down (SStatus 0 SControl F300)
Freeing init memory: 216K
/init: line 9: /usr/sbin/depmod: No such file or directory
====== Entering initramfs(/init) ======
grep: /var/tmp/signatureinfo: No such file or directory
grep: /var/tmp/signatureinfo: No such file or directory
grep: /var/tmp/signatureinfo: No such file or directory
grep: /var/tmp/signatureinfo: No such file or directory
grep: /var/tmp/signatureinfo: No such file or directory
grep: /var/tmp/signatureinfo: No such file or directory
grep: /var/tmp/signatureinfo: No such file or directory
grep: /var/tmp/signatureinfo: No such file or directory
CANDIDATE_NUM=0 : CANDIDATE_LIST=
Selecting disk with not considering signature
CANDIDATE_NUM=0 : CANDIDATE_LIST=
libsys: nas_feature : using /root/.nas_features/JP/0x0000201E
Checking the existance of micon ...
#[miconapl.mcon_get_version]
mcon_version=TS-M Series V1.03
libsys: /etc/sysctl.conf : using /root/.params/sysctl/0x0000201E
ls: /dev/rtc: No such file or directory
libsys: /dev/rtc was updated : /dev/rtc 254 0
Wed Nov 14 00:15:54 2007 -0.991086 seconds
Wed Nov 14 00:15:54 JST 2007
LibSys_GetUsbDiskStartNum : Usb device not found(/sys/block/sda/device). Returning 1
grep: /var/tmp/devlink: No such file or directory
create_devlink:Using new routine.
console
panic
mtdparts
ubi.mtd
BOOTVER
UBOOT_DATE
nandboot
linuxrc:choose operation (timeout 4[s])
1:RamRoot 2:NfsRoot 3:sda1 4:sda2 other:HddRoot ?
***** USB or NAND boot detected. *****
***** Entering EM mode forcefully *****
-RamdiskRoot-
--- rcStart (initrd) ---
mount: mounting proc on /proc failed: Device or resource busy
mount: mounting sysfs on /sys failed: Device or resource busy
Cannot set device ring parameters: Operation not supported
Cannot set device ring parameters: Operation not supported
Cannot set device ring parameters: Operation not supported
Cannot set device ring parameters: Operation not supported
Cannot get device ring settings: No such device
Cannot get device ring settings: No such device
Cannot get device ring settings: No such device
Cannot get device ring settings: No such device
=== checkroot.sh ===
grep: /var/tmp/devlink: No such file or directory
create_devlink:Using new routine.
Unable to find swap-space signature
swapon: /dev/md2: Invalid argument
/sbin/hotplug [block]
/sbin/hotplug [bdi]
create dir : /var/www
=== create_devlink.sh ===
create_devlink:Using new routine.
=== startSysMd.sh ===
-- rebuild mdadm.conf for BOOT, ROOTFS with Intelligent routine --
checkDiskStatus : disk1 unplugged
checkDiskStatus : disk2 unplugged
checkDiskStatus : disk3 unplugged
checkDiskStatus : disk4 unplugged
checkDiskPerformanceParallel : disk1 unplugged
checkDiskPerformanceParallel : disk2 unplugged
checkDiskPerformanceParallel : disk3 unplugged
checkDiskPerformanceParallel : disk4 unplugged
checkDiskPerformanceParallel : Waiting for performance check will be done(timeout=20).
checkDiskPerformanceParallel : Disk which has performance lower than 30 MB/s will be kicked out.
checkDiskPerformanceParallel : disk1 performance test skipped(unplugged)
checkDiskPerformanceParallel : disk2 performance test skipped(unplugged)
checkDiskPerformanceParallel : disk3 performance test skipped(unplugged)
checkDiskPerformanceParallel : disk4 performance test skipped(unplugged)
mount: mounting /dev/disk1_1 on /tmp/boot_test failed: No such file or directory
mount: mounting /dev/disk2_1 on /tmp/boot_test failed: No such file or directory
mount: mounting /dev/disk3_1 on /tmp/boot_test failed: No such file or directory
mount: mounting /dev/disk4_1 on /tmp/boot_test failed: No such file or directory
libmd: GetMdBaseDisk : Selected 0
mdadm: cannot open /dev/disk?_1: No such file or directory
mdadm: cannot open /dev/disk??_1: No such file or directory
mdadm: cannot open /dev/disk?_2: No such file or directory
mdadm: cannot open /dev/disk??_2: No such file or directory
mdadm: cannot open /dev/disk?_5: No such file or directory
mdadm: cannot open /dev/disk??_5: No such file or directory
mdadm: No devices listed in conf file were found.
-- setup max error counts --
/sys/block/md0/md/maxerr_cnt is setted to 1000
/usr/local/lib/libmd: line 775: /sys/block/md0/md/maxerr_cnt: No such file or directory
/sys/block/md1/md/maxerr_cnt is setted to 1000
/usr/local/lib/libmd: line 775: /sys/block/md1/md/maxerr_cnt: No such file or directory
/sys/block/md2/md/maxerr_cnt is setted to 1000
/usr/local/bin/hdd_raid_syncspeed.sh: line 147: /sys/block/md0/md/sync_speed_max: No such file or directory
/usr/local/bin/hdd_raid_syncspeed.sh: line 147: /sys/block/md1/md/sync_speed_max: No such file or directory
/usr/local/bin/hdd_raid_syncspeed.sh: line 147: /sys/block/md2/md/sync_speed_max: No such file or directory
=== fwupdate.sh ===
umount: can't umount /boot: Invalid argument
mkdir: can't create directory '/boot': File exists
EXT3-fs (md0): error: unable to read superblock
/sbin/hotplug [block]
/sbin/hotplug [bdi]
EXT2-fs (md0): error: unable to read superblock
EXT4-fs (md0): unable to read superblock
FAT-fs (md0): unable to read boot sector
FAT-fs (md0): unable to read boot sector
isofs_fill_super: bread failed, dev=md0, iso_blknum=16, block=32
/sbin/hotplug [block]
/sbin/hotplug [bdi]
/sbin/hotplug [block]
/sbin/hotplug [bdi]
/sbin/hotplug [bdi]
/sbin/hotplug [block]
/sbin/hotplug [bdi]
/sbin/hotplug [block]
mount: mounting /dev/md0 on /boot failed: Input/output error
=== closeSysMd.sh ===
md: md0 stopped.
mdadm: stopped /dev/md0
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [bdi]
/sbin/hotplug [bdi]
/sbin/hotplug [block]
md: md1 stopped.
/sbin/hotplug [block]
/sbin/hotplug [block]
mdadm: stmd: md2 stopped.
opped /dev/md1
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [bdi]
mdadm: stopped /dev/md2
=== sethostname.sh ===
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [bdi]
/sbin/hotplug [block]
configure files from Buffalo parameters.
=== restore_config.sh ===
-- rebuild mdadm.conf for BOOT --
mdadm: cannot open /dev/disk?_1: No such file or directory
mdadm: cannot open /dev/disk??_1: No such file or directory
mdadm: No devices listed in conf file were found.
-- setup max error cEXT3-fs (md0): error: unable to read superblock
ounts --
/sys/block/md0/md/maxerr_cnt is setted to 1000
/usr/local/lib/libmd: line 775: /sys/block/md0/md/maxerr_cnt: No such file or directory
/sbin/hotplug [block]
/sbin/hotplug [bdi]
EXT2-fs (md0): error: unable to read superblock
EXT4-fs (md0): unable to read superblock
FAT-fs (md0): unable to read boot sector
FAT-fs (md0): unable to read boot sector
isofs_fill_super: bread failed, dev=md0, iso_blknum=16, block=32
/sbin/hotplug [bdi]
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [bdi]
/sbin/hotplug [bdi]
/sbin/hotplug [block]
/sbin/hotplug [bdi]
/sbin/hotplug [block]
mount: mounting /dev/md0 on /boot failed: Input/output error
Restore previous configuration files
tar (child): /boot/conf_save.tgz: Cannot open: No such file or directory
tar (child): Error is not recoverable: exiting now
/bin/tar: Child returned status 2
/bin/tar: Error is not recoverable: exiting now
tar (child): /boot/conf_save.tgz: Cannot open: No such file or directory
tar (child): Error is not recoverable: exiting now
/bin/tar: Child returned status 2
/bin/tar:md: md0 stopped.
Error is not recoverable: exiting now
unzip fail.
/tmp/etc/localtime ->
umount: can't umount /boot: Invalid argument
rootfs on / type rootfs (rw,relatime)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)md: md1 stopped.
devpts on /dev/pts type devpts (rw,relatime,gid=4,mode=620)
/dev/ram1 on /mnt/ram type tmpfs (rw,relatime,size=15360k)
PID USER COMMAND
1 root init
2 root [kthreadd]
3 root [ksoftirqd/0]
4 root [kworker/0:0]
5 root [kworker/u:0]
6 root [migration/0]
7 root [migramd: md2 stopped.
tion/1]
8 root [kworker/1:0]
9 root [ksoftirqd/1]
10 root [khelper]
11 root [kdevtmpfs]
12 root [kworker/u:1]
154 root [sync_supers]
156 root [bdi-default]
158 root [kblockd]
165 root [ata_sff]
175 root [md]
195 root [rpciod]
196 root [kworker/0:1]
212 root [kswapd0]
263 root [fsnotify_mark]
280 root [nfsiod]
299 root [xfs_mru_cache]
300 root [xfslogd]
301 root [xfsdatad]
302 root [xfsconvertd]
304 root [crypto]
415 root [scsi_eh_0]
418 root [scsi_eh_1]
421 root [scsi_eh_2]
424 root [scsi_eh_3]
427 root [kworker/u:2]
428 root [kworker/u:3]
429 root [kworker/u:4]
430 root [kworker/u:5]
438 root [scsi_eh_4]
441 root [scsi_eh_5]
444 root [kworker/u:6]
445 root [kworker/u:7]
456 root [mtdblock0]
462 root [mtdblock1]
468 root [kworker/1:1]
471 root [ubi_bgt0d]
742 root {rcS} /bin/sh /etc/init.d/rcS
1127 root [kworker/0:2]
1164 root {restore_config.} /bin/sh /etc/init.d/restore_config.sh start
1208 root ps
mdadm: stopped /dev/md0
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [bdi]
/sbin/hotplug [block]
/sbin/hotplug [bdi]
/sbin/hotplug [block]
mdadm: stopped /dev/md1
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [bdi]
/sbin/hotplug [block]
/sbin/hotplug [bdi]
mdadm: stopped /dev/md2
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [bdi]
grep: /etc/melco/iscsi_info: No such file or directory
Can't open /etc/melco/iscsi_info: No such file or directory.
=== EnablingAutoip.sh ===
=== networking.sh ===
/etc/init.d/networking.sh : Clear /etc/dhcpc/dhcpcd-eth0.pid eth0
/etc/init.d/networking.sh : Clear /etc/dhcpc/dhcpcd-eth1.pid eth1
/etc/init.d/networking.sh : Clear /etc/dhcpc/dhcpcd-bond0.pid bond0
/etc/init.d/networking.sh : Read dhcpc file
/etc/init.d/networking.sh : configure :
create network files.. (eth0)
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
create network files.. (eth1)
IP=[dhcp], netmask=[], dgw=[]
killall: dhcpcd: no process killed
/etc/init.d/networking.sh: line 91: /etc/init.d/networking.sh : Delete /etc/dhcpc/dhcpcd-.pid: No such file or directory
Configuration network interface: lo eth0 eth1
/sbin/ifconfig eth0 mtu 1500 multicast
/sbin/ifconfig eth1 mtu 1500 multicast
requesting DHCP tout=30[s]
networking.sh: dhcp requesting...
DontDownIfacepool #1: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added
alwaysFork
eth1: started
** eth1 : networking.sh dhcp fin.
requesting DHCP tout=30[s]
networking.sh: dhcp requesting...
SIOCGIFADDR :Cannot assign requested address
Dopool #0: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added
ntDownIface
alweth0: started
aysFork
sendto: count 6 sync 1
sendto: count 5 sync 1
** eth0 : networking.sh dhcp fin.
Waiting 1294 ...sendto: count 6 sync 1
sendto: count 4 sync 1
sendto: count 5 sync 1
sendto: count 3 sync 1
sendto: count 4 sync 1
sendto: count 2 sync 1
sendto: count 3 sync 1
sendto: count 1 sync 1
sendto: count 2 sync 1
sendto: count 0 sync 1
dhcpInit call AutoipBound
setAutoIP eth1 called
MAC address = 10:6f:3f:xx:xx:8f
file name /etc/dhcpc/autoip-eth1.info
/sbin/ifconfig eth1 169.254.242.46 netmask 255.255.0.0 up
sendto: count 1 sync 1
sendto: count 0 sync 1
dhcpInit call AutoipBound
setAutoIP eth0 called
MAC address = 10:6f:3f:xx:xx:8e
file name /etc/dhcpc/autoip-eth0.info
/sbin/ifconfig eth0 169.254.136.74 netmask 255.255.0.0 up
Arp result 0
/etc/init.d/rService
finished.
Waiting 1298 ...Arp result 0
/etc/init.d/rService
finished.
Checking network address for each network device
Warn!!! eth0 and eth1 has same network address!
Waiting fot linkup detection
..........networking.sh: Each network is not same in physically(or virtually).
networking.sh: Shutting down eth1
eth1: stopped
eth1: started
networking.sh: arp_newip_notify_sub : executing arping -A 169.254.136.74 -I eth0 -c 1
networking.sh: arp_newip_notify_sub : Can't get ipaddr of eth1.
add default if
configure files from Buffalo parameters.
=== syslog.sh ===
using /sbin/syslogd
using /sbin/klogd
Starting system logger: load_info ItemValue = off
LoadConfFileStringEx:key=[ad_dns] not found in /etc/melco/info.
LoadConfFileOnOffEx:key=[info_visible] not found in /etc/melco/info.
LoadConfFileStringEx:key=[array2] not found in /etc/melco/diskinfo.
LoadConfFileStringEx:key=[disk3] not found in /etc/melco/diskinfo.
LoadConfFileStringEx:key=[disk4] not found in /etc/melco/diskinfo.
LoadConfFileStringEx:key=[usb_disk3] not found in /etc/melco/diskinfo.
LoadConfFileStringEx:key=[usb_disk4] not found in /etc/melco/diskinfo.
LoadConfFileOnOffEx:key=[smb2] not found in /etc/melco/info.
LoadConfFileOnOffEx:key=[recycle_admin] not found in /etc/melco/info.
LoadConfFileOnOffEx:key=[recycle_macinfo] not found in /etc/melco/info.
Starting kernel logger:
=== kernelmon.sh ===
Starting kernelmon:=== miconmon.sh ===
KERNELMOn (SATA 0 unplugged)
KERNELMOn (SATA 1 unplugged)
KERNELMOn (SATA 2 unplugged)
KERNELMOn (SATA 3 unplugged)
KERNELMOn (lanact 0 half eth0)
=== usb.sh ===
/etc/init.d/usb.sh: line 97: depmod: command not found
/sbin/hotplug [module]
/sbin/hotplug [module]
/sbin/hotplug [bus]
usbcore: registered new interface driver usbfs
/sbin/hotplug [drivers]
/sbin/hotplug [class]
usbcore: registered new interface driver hub
/sbin/hotplug [drivers]
KERNELMOn (lanacusbcore: registered new device driver usb
t 0 half eth1)
/sbin/hotplug [drivers]
xhci_hcd 0000:01:01.0: xHCI Host Controller
xhci_hcd 0000:01:01.0: new USB bus registered, assigned bus number 1
/sbin/hotplug [module]
xhci_hcd 0000:01:01.0: irq 62, io mem 0xe8000000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: xHCI Host Controller
usb usb1: Manufacturer: Linux 3.3.4 xhci_hcd
usb usb1: SerialNumber: 0000:01:01.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
/sbin/hotplug [usb]
xhci_hcd 0000:01:01.0: xHCI Host Controller
xhci_hcd 0000:01:01.0: new USB bus registered, assigned bus number 2
/sbin/hotplug [uusb usb2: New USB device found, idVendor=1d6b, idProduct=0003
sb_device]
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: xHCI Host Controller
usb usb2: Manufacturer: Linux 3.3.4 xhci_hcd
/sbin/hotplug [uusb usb2: SerialNumber: 0000:01:01.0
sb]
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
/sbin/hotplug [usb]
/sbin/hotplug [usb]
/sbin/hotplug [usb_device]
/sbin/hotplug [drivers]
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_marvell ehci_marvell.0: Marvell Orion EHCI
ehci_marvell ehci_marvell.0: new USB bus registered, assigned bus number 3
/sbin/hotplug [module]
ehci_marvell ehci_marvell.0: irq 45, io base 0xfbb50100
ehci_marvell ehci_marvell.0: USB 2.0 started, EHCI 1.00
usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: Marvell Orion EHCI
usb usb3: Manufacturer: Linux 3.3.4 ehci_hcd
usb usb3: SerialNumber: ehci_marvell.0
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
/sbin/hotplug [usb]
/sbin/hotplug [usb]
ehci_marvell ehci_marvell.1: Marvell Orion EHCI
ehci_marvell ehci_marvell.1: new USB bus registered, assigned bus number 4
/sbin/hotplug [usb_device]
ehci_marvell ehci_marvell.1: irq 46, io base 0xfbb51100
ehci_marvell ehci_marvell.1: USB 2.0 started, EHCI 1.00
usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: Marvell Orion EHCI
usb usb4: Manufacturer: Linux 3.3.4 ehci_hcd
usb usb4: SerialNumber: ehci_marvell.1
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
/sbin/hotplug [usb]
/sbin/hotplug [usb]
ehci_marvell ehci_marvell.2: Marvell Orion EHCI
ehci_marvell ehci_marvell.2: new USB bus registered, assigned bus number 5
/sbin/hotplug [usb_device]
ehci_marvell ehci_marvell.2: irq 47, io base 0xfbb52100
ehci_marvell ehci_marvell.2: USB 2.0 started, EHCI 1.00
usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: Marvell Orion EHCI
usb usb5: Manufacturer: Linux 3.3.4 ehci_hcd
usb usb5: SerialNumber: ehci_marvell.2
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 1 port detected
/sbin/hotplug [usb]
/sbin/hotplug [usb]
/sbin/hotplug [usb_device]
/sbin/hotplug [drivers]
/sbin/hotplug [drivers]
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
/sbin/hotplug [module]
/sbin/hotplug [drivers]
uhci_hcd: USB Universal Host Controller Interface driver
/sbin/hotplug [module]
/sbin/hotplug [drivers]
usbcore: registered new interface driver libusual
/sbin/hotplug [module]
/sbin/hotplug [module]
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
/sbin/hotplug [drivers]
usbcore: registered new interface driver usblp
/sbin/hotplug [module]
/sbin/hotplug [drivers]
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
/sbin/hotplug [module]
/sbin/hotplug [drivers]
/sbin/hotplug [drivers]
grep: /etc/melco/usbshareinfo: No such file or directory
/usr/local/lib/libsys: line 1154: sqlite3: command not found
grep: /etc/melco/usbshareinfo: No such file or directory
/usr/local/lib/libsys: line 1154: sqlite3: command not found
grep: /etc/melco/usbshareinfo: No such file or directory
/usr/local/lib/libsys: line 1154: sqlite3: command not found
grep: /etc/melco/usbshareinfo: No such file or directory
/usr/local/lib/libsys: line 1154: sqlite3: command not found
/usr/local/lib/libsys: line 1179: sqlite3: command not found
/usr/local/lib/libsys: line 1179: sqlite3: command not found
/usr/local/lib/libsys: line 1179: sqlite3: command not found
/usr/local/lib/libsys: line 1179: sqlite3: command not found
/usr/local/lib/libsys: line 1191: sqlite3: command not found
/usr/local/lib/libsys: line 1191: sqlite3: command not found
/usr/local/lib/libsys: line 1191: sqlite3: command not found
/usr/local/lib/libsys: line 1191: sqlite3: command not found
=== clientUtil_servd.sh ===
Starting clientUtil_server:
->Starting on eth1
->Starting on eth0
=== daemonwatch.sh ===
=== bootcomplete.sh ===
No need to run drivecheck.sh
BuffaloGpio_ChangePowerStatus > Writing 0x71
/usr/local/bin/hdd_raid_syncspeed.sh: line 147: /sys/block/md0/md/sync_speed_max: No such file or directory
/usr/local/bin/hdd_raid_syncspeed.sh: line 147: /sys/block/md1/md/sync_speed_max: No such file or directory
/usr/local/bin/hdd_raid_syncspeed.sh: line 147: /sys/block/md2/md/sync_speed_max: No such file or directory
hdd_raid_syncspeed.sh: Adding EDP md devices
hdd_raid_syncspeed.sh: USERLAND_MD=md10 md11 md12 md13 md14 md20 md21 md22 md23 md24 md101 md102 md103 md104
=== micon_setup.sh ===
SIOCGIFADDR :Cannot assign requested address
/usr/local/bin/change_notify.sh:RAIDMODE on LCD is not supported on this model.
=== late_inspection_phase.sh ===
=== buffalo_rescue.sh ===
BuffaloGpio_ChangePowerStatus > Writing 0x71
shutdown_start.sh #4: miconapl -a shutdown_wait done.
eth0: stopped
eth1: stopped
/sbin/hotplug [bdi]
/sbin/hotplug [block]
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to all processes
Requesting system poweroff
Shutting Down Marvell Ethernet Driver
System halted.
port 0 : Magic mode WoL disabled.
port 1 : Magic mode WoL disabled.
micon : Disabling WOL...
>miconCntl_WolDisable
>miconCntl_PowerOff
>miconCntl_ShutdownWait
大破雑記帳 