Due to changes in design, advancement in techniques, and general interest of labor and industry i... more Due to changes in design, advancement in techniques, and general interest of labor and industry in safety, the Sectional Committee, under the joint sponsorship of ASME and the Bureau of Yards and Docks (now the Naval Facilities Engineering Command) was reorganized on January 31, 1962, with 39 members representing 27 national organizations. The new Committee changed the format of ASA B30.2-1943 so that the multitude of equipment types it addressed could be published in separate volumes that could completely cover the construction, installation, inspection, testing, maintenance, and operation of each type of equipment that was included in the scope of ASA B30.2. This format change resulted in the initial publication of B30.3, B30.5, B30.6, B30.11, and B30.16 being designated as revisions of B30.2 with the remainder of the B30 volumes being published as totally new volumes. ASA changed its name to USASI in 1966 and to ANSI in 1969, which resulted in B30 volumes from 1943 to 1968 being designated as ASA B30, USAS B30, or ANSI B30, depending on their date of publication. In 1982, the Committee was reorganized as an Accredited Organization Committee, operating under procedures developed by ASME and accredited by ANSI. This Standard presents a coordinated set of rules that may serve as a guide to government and other regulatory bodies and municipal authorities responsible for the guarding and inspection of the equipment falling within its scope. The suggestions leading to accident prevention are given both as mandatory and advisory provisions; compliance with both types may be required by employers of their employees. In case of practical difficulties, new developments, or unnecessary hardship, the administrative or regulatory authority may grant variances from the literal requirements or permit the use of other devices or methods, but only when it is clearly evident that an equivalent degree of protection is thereby secured. To secure uniform application and interpretation of this Standard, administrative or regulatory authorities are urged to consult the B30 Committee, in accordance with the format described in Section IX of the Introduction, before rendering decisions on disputed points. Safety codes and standards are intended to enhance public safety. Revisions result from committee consideration of factors such as technological advances, new data, and changing environmental and industry needs. Revisions do not imply that previous editions were inadequate. The first edition of ASME B30.
The next edition of this Standard is scheduled for publication in 2021. This Standard will become... more The next edition of this Standard is scheduled for publication in 2021. This Standard will become effective 1 year after the Date of Issuance. ASME issues written replies to inquiries concerning interpretations of technical aspects of this Standard. Interpretations are published on the Committee Web page and under go.asme.org/ InterpsDatabase. Errata to codes and standards may be posted on the ASME Web site under the Committee Pages to provide corrections to incorrectly published items, or to correct typographical or grammatical errors in codes and standards. Such errata shall be used on the date posted. The Committee Pages can be found at http://cstools.asme.org/. There is an option available to automatically receive an e-mail notification when errata are posted to a particular code or standard. This option can be found on the appropriate Committee Page after selecting "Errata" in the "Publication Information" section. ASME is the registered trademark of The American Society of Mechanical Engineers. This code or standard was developed under procedures accredited as meeting the criteria for American National Standards. The Standards Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate. The proposed code or standard was made available for public review and comment that provides an opportunity for additional public input from industry, academia, regulatory agencies, and the public-at-large. ASME does not "approve," "rate," or "endorse" any item, construction, proprietary device, or activity. ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable letters patent, nor assumes any such liability. Users of a code or standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard. ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME procedures and policies, which precludes the issuance of interpretations by individuals. No part of this document may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher.
se publicaron como volúmenes totalmente nuevos. ASA cambió su nombre a USASI en 1966 y a ANSI en ... more se publicaron como volúmenes totalmente nuevos. ASA cambió su nombre a USASI en 1966 y a ANSI en 1969, lo que resultó en que los volúmenes B30 de 1943 a 1968 fueran designados como ASAB30, USASB30 o ANSI B30, según su fecha de publicación. En 1982, el Comité se reorganizó como un Comité de Organización Acreditado que opera bajo procedimientos desarrollados por ASME y acreditados por ANSI. Entre 1920 y 1925 se llevaron a cabo reuniones y debates sobre la seguridad en grúas, cabrias y polipastos en los que participaron el Comité de correlación del Código de seguridad de ASME, la Asociación de ingenieros eléctricos del hierro y el acero, el Museo estadounidense de seguridad, el Comité de estándares de ingeniería estadounidense (AESC) [modificado posteriormente a la Asociación Estadounidense de Estándares (ASA), luego
Due to changes in design, advancement in techniques, and general interest of labor and industry i... more Due to changes in design, advancement in techniques, and general interest of labor and industry in safety, the Sectional Committee, under the joint sponsorship ofASME and the Bureau ofYards and Docks (now the Naval Facilities Engineering Command), was reorganized on January 31, 1962, with 39 members representing 27 national organizations. The new committee changed the format of ASA B30.2-1943 so that the multitude of equipment types it addressed could be published in separate volumes that could completely cover the construction, installation, inspection, testing, maintenance, and operation of each type of equipment that was included in the scope of ASA B30.2. This format change resulted in the initial publication of B30.3, B30.5, B30.6, B30.11, and B30.16 being designated as "Revisions" of B30.2 with the remainder ofthe B30 volumes being published as totally new volumes. ASA changed its name to USASI in 1966 and to ANSI in 1969, which resulted in B30 volumes from 1943 to 1968 being designated as "ASA B30," "USAS B30" or "ANSI B30" depending on their date of publication. In 1982, the committee was reorganized as an Accredited Organization Committee, operating under procedures developed by ASME and accredited by ANSI. This Standard presents a coordinated set of rules that may serve as a guide to government and other regulatory bodies and municipal authorities responsible for the guarding and inspection of the equipment falling within its scope. The suggestions leading to accident prevention are given as both mandatory and advisory provisions; compliance with both types may be required by employers of their employees. In case ofpractical difficulties, new developments, or unnecessary hardship, the administrative or regulatory authority may grant variances from the literal requirements or permit the use ofother devices or methods, but only when it is clearly evident that an equivalent degree of protection is thereby secured. To secure uniform application and interpretation of this Standard, administrative or regulatory authorities are urged to consult the B30 Committee in accordance with the format described in Section IX of the B30 Standard Introduction, before rendering decisions on disputed points. Safety codes and standards are intended to enhance public safety. Revisions result from committee consideration of factors such as technological advances, new data, and changing environmental and industry needs. Revisions do not imply that previous editions were inadequate. The ASME B30.5-2007 edition added responsibilities to be assigned in the worksite organization. The 2011 edition included minor revisions and the addition of Nonmandatory Appendix A on critical lifts. The 2014 edition incorporated many global B30 changes including the addition of personnel competence and translation requirements as well as other revisions made throughout the document. This 2018 edition revises the Crane Operation in the Vicinity of Electric Power Lines section entirely, adds a new section on Rigger Responsibilities, and incorporates other miscellaneous revisions. This edition of the B30.5 Volume was approved by the B30 Committee and by ASME, and was approved by ANSI and designated as an American National Standard on
Due to changes in design, advancement in techniques, and general interest of labor and industry i... more Due to changes in design, advancement in techniques, and general interest of labor and industry in safety, the Sectional Committee, under the joint sponsorship of ASME and the Bureau of Yards and Docks (now the Naval Facilities Engineering Command), was reorganized on January 31, 1962, with 39 members representing 27 national organizations. The new Committee changed the format of ASA B30.2-1943 so that the multitude of equipment types it addressed could be published in separate volumes that could completely cover the construction, installation, inspection, testing, maintenance, and operation of each type of equipment that was included in the scope of ASA B30.2. This format change resulted in B30.3, B30.5, B30.6, B30.11, and B30.16 being initially published as "Revisions" of B30.2, with the remainder of the B30 volumes being published as totally new volumes. ASA changed its name to USASI in 1966 and to ANSI in 1969, which resulted in B30 volumes from 1943 to 1968 being designated as ASA B30, USAS B30, or ANSI B30, depending on their date of publication. In 1982, the Committee was reorganized as an Accredited Organization Committee operating under procedures developed by ASME and accredited by ANSI. This Standard presents a coordinated set of rules that may serve as a guide to government and other regulatory bodies and municipal authorities responsible for the guarding and inspection of the equipment falling within its scope. The suggestions leading to accident prevention are given both as mandatory and advisory provisions; compliance with both types may be required by employers of their employees. In case of practical difficulties, new developments, or unnecessary hardship, the administrative or regulatory authority may grant variances from the literal requirements or permit the use of other devices or methods, but only when it is clearly evident that an equivalent degree of protection is thereby secured. To secure uniform application and interpretation of this Standard, administrative or regulatory authorities are urged to consult the B30 Committee, in accordance with the format described in Section IX of the B30 Standard Introduction, before rendering decisions on disputed points. Safety codes and standards are intended to enhance public safety. Revisions result from committee consideration of factors such as technological advances, new data, and changing environmental and industry needs. Revisions do not imply that previous editions were inadequate.
The next edition of this Standard is scheduled for publication in 2018. This Standard will become... more The next edition of this Standard is scheduled for publication in 2018. This Standard will become effective 1 year after the Date of Issuance. ASME issues written replies to inquiries concerning interpretations of technical aspects of this Standard. Interpretations are published on the ASME Web site under the Committee Pages at http://cstools.asme.org/ as they are issued. Interpretations will also be included with each edition. Errata to codes and standards may be posted on the ASME Web site under the Committee Pages to provide corrections to incorrectly published items, or to correct typographical or grammatical errors in codes and standards. Such errata shall be used on the date posted. The Committee Pages can be found at http://cstools.asme.org/. There is an option available to automatically receive an e-mail notification when errata are posted to a particular code or standard. This option can be found on the appropriate Committee Page after selecting "Errata" in the "Publication Information" section. ASME is the registered trademark of The American Society of Mechanical Engineers. This code or standard was developed under procedures accredited as meeting the criteria for American National Standards. The Standards Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate. The proposed code or standard was made available for public review and comment that provides an opportunity for additional public input from industry, academia, regulatory agencies, and the public-at-large. ASME does not "approve," "rate," or "endorse" any item, construction, proprietary device, or activity. ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable letters patent, nor assumes any such liability. Users of a code or standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard. ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME procedures and policies, which precludes the issuance of interpretations by individuals. No part of this document may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher.
fue presentado a la reunión anual de ASME. Las reuniones y discusiones relacionadas a la segurida... more fue presentado a la reunión anual de ASME. Las reuniones y discusiones relacionadas a la seguridad de las grúas, grúas de brazo móvil y winches se celebraron desde 1920 hasta 1925, con la participación del
y un grupo de empresas vascas especializadas en este tipo de trabajos por establecer un procedimi... more y un grupo de empresas vascas especializadas en este tipo de trabajos por establecer un procedimiento y unas medidas preventivas para que las labores que se realizan en este sector cumplan los requisitos de seguridad y salud laboral necesarios. Con esta inquietud se formó un grupo de especialistas provenientes de empresas de estabilización de taludes, alquiladoras de gruas, Coordinación de Seguridad y Salud, Servicios de Prevención y los propios técnicos de OSALAN, para dar respuesta a la problemática de seguridad que tradicionalmente se ha presentado en la realización de estos trabajos y que, por sus riesgos, merecen un especial tratamiento. Fruto de este proceso de trabajo es esta guía que tiene por objetivo servir de herramienta útil tanto a las empresas como a los propios técnicos del ramo. Para confeccionar esta guía, se ha partido de una evaluación de riesgos (incluida al final de la misma) que ha servido de base para la redacción de un Procedimiento de Trabajo, que se completa con un "chek list". Considero que es un reto para todos conseguir la implantación de este procedimiento que se convertirá en un primer y muy importante paso para minimizar los riesgos de una actividad que sigue sin ser contemplada en la mayor parte de los proyectos de ejecución de las obras. En este sentido, espero que esta Guía se convierta en una herramienta de gran valor práctico.
La norma B30.1 se aplica a gatos de propósito general y portátil de las siguientes categorías: Ga... more La norma B30.1 se aplica a gatos de propósito general y portátil de las siguientes categorías: Gatos hidráulicos manuales o motorizados, gatos mecánicos de trinquete, y martinetes manuales o mecánicos de accionamiento eléctrico. Gatos diseñados para servicio automotriz, trip-lowered jacks, y los que son una parte integral de otros equipos NO están incluidos en el alcance de esta Norma. Los dispositivos diseñados para el soporte estático en lugar de levantar no están incluidos.
Grúas móviles y sobre riel (de vía) Normas de seguridad para cablecarriles, grúas, derricks (cabr... more Grúas móviles y sobre riel (de vía) Normas de seguridad para cablecarriles, grúas, derricks (cabrias), elevadores, ganchos, gatos y eslingas UNA NORMA NACIONAL AMERICANA ASME B30.5-2007 (Revisión de ASME B30.5-2004) ii Fecha de emisión: 7 de marzo de 2008 La publicación de la próxima edición de esta Norma está prevista para el 2010. No habrá addenda para esta edición. ASME responde por escrito a las preguntas relativas a la interpretación de los aspectos técnicos de la presente Norma. Las interpretaciones son publicadas en el sitio Web de ASME en el marco del Committee Pages, en http://cstools.asme.org/ a medida que se emiten y también se publicarán en la próxima edición de la Norma.
The next edition of this Standard is scheduled for publication in 2018. This Standard will become... more The next edition of this Standard is scheduled for publication in 2018. This Standard will become effective 1 year after the Date of Issuance. ASME issues written replies to inquiries concerning interpretations of technical aspects of this Standard. Interpretations are published on the ASME Web site under the Committee Pages at http://cstools.asme.org/ as they are issued. Interpretations will also be included with each edition. Errata to codes and standards may be posted on the ASME Web site under the Committee Pages to provide corrections to incorrectly published items, or to correct typographical or grammatical errors in codes and standards. Such errata shall be used on the date posted. The Committee Pages can be found at http://cstools.asme.org/. There is an option available to automatically receive an e-mail notification when errata are posted to a particular code or standard. This option can be found on the appropriate Committee Page after selecting "Errata" in the "Publication Information" section. ASME is the registered trademark of The American Society of Mechanical Engineers. This code or standard was developed under procedures accredited as meeting the criteria for American National Standards. The Standards Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate. The proposed code or standard was made available for public review and comment that provides an opportunity for additional public input from industry, academia, regulatory agencies, and the public-at-large. ASME does not "approve," "rate," or "endorse" any item, construction, proprietary device, or activity. ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable letters patent, nor assumes any such liability. Users of a code or standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard. ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME procedures and policies, which precludes the issuance of interpretations by individuals. No part of this document may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher.
Due to changes in design, advancement in techniques, and general interest of labor and industry i... more Due to changes in design, advancement in techniques, and general interest of labor and industry in safety, the Sectional Committee, under the joint sponsorship of ASME and the Bureau of Yards and Docks (now the Naval Facilities Engineering Command) was reorganized on January 31, 1962, with 39 members representing 27 national organizations. The new Committee changed the format of ASA B30.2-1943 so that the multitude of equipment types it addressed could be published in separate volumes that could completely cover the construction, installation, inspection, testing, maintenance, and operation of each type of equipment that was included in the scope of ASA B30.2. This format change resulted in the initial publication of B30.3, B30.5, B30.6, B30.11, and B30.16 being designated as revisions of B30.2 with the remainder of the B30 volumes being published as totally new volumes. ASA changed its name to USASI in 1966 and to ANSI in 1969, which resulted in B30 volumes from 1943 to 1968 being designated as ASA B30, USAS B30, or ANSI B30, depending on their date of publication. In 1982, the Committee was reorganized as an Accredited Organization Committee, operating under procedures developed by ASME and accredited by ANSI. This Standard presents a coordinated set of rules that may serve as a guide to government and other regulatory bodies and municipal authorities responsible for the guarding and inspection of the equipment falling within its scope. The suggestions leading to accident prevention are given both as mandatory and advisory provisions; compliance with both types may be required by employers of their employees. In case of practical difficulties, new developments, or unnecessary hardship, the administrative or regulatory authority may grant variances from the literal requirements or permit the use of other devices or methods, but only when it is clearly evident that an equivalent degree of protection is thereby secured. To secure uniform application and interpretation of this Standard, administrative or regulatory authorities are urged to consult the B30 Committee, in accordance with the format described in Section IX of the Introduction, before rendering decisions on disputed points. Safety codes and standards are intended to enhance public safety. Revisions result from committee consideration of factors such as technological advances, new data, and changing environmental and industry needs. Revisions do not imply that previous editions were inadequate. The first edition of ASME B30.
The next edition of this Standard is scheduled for publication in 2021. This Standard will become... more The next edition of this Standard is scheduled for publication in 2021. This Standard will become effective 1 year after the Date of Issuance. ASME issues written replies to inquiries concerning interpretations of technical aspects of this Standard. Interpretations are published on the Committee Web page and under go.asme.org/ InterpsDatabase. Errata to codes and standards may be posted on the ASME Web site under the Committee Pages to provide corrections to incorrectly published items, or to correct typographical or grammatical errors in codes and standards. Such errata shall be used on the date posted. The Committee Pages can be found at http://cstools.asme.org/. There is an option available to automatically receive an e-mail notification when errata are posted to a particular code or standard. This option can be found on the appropriate Committee Page after selecting "Errata" in the "Publication Information" section. ASME is the registered trademark of The American Society of Mechanical Engineers. This code or standard was developed under procedures accredited as meeting the criteria for American National Standards. The Standards Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate. The proposed code or standard was made available for public review and comment that provides an opportunity for additional public input from industry, academia, regulatory agencies, and the public-at-large. ASME does not "approve," "rate," or "endorse" any item, construction, proprietary device, or activity. ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable letters patent, nor assumes any such liability. Users of a code or standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard. ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME procedures and policies, which precludes the issuance of interpretations by individuals. No part of this document may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher.
se publicaron como volúmenes totalmente nuevos. ASA cambió su nombre a USASI en 1966 y a ANSI en ... more se publicaron como volúmenes totalmente nuevos. ASA cambió su nombre a USASI en 1966 y a ANSI en 1969, lo que resultó en que los volúmenes B30 de 1943 a 1968 fueran designados como ASAB30, USASB30 o ANSI B30, según su fecha de publicación. En 1982, el Comité se reorganizó como un Comité de Organización Acreditado que opera bajo procedimientos desarrollados por ASME y acreditados por ANSI. Entre 1920 y 1925 se llevaron a cabo reuniones y debates sobre la seguridad en grúas, cabrias y polipastos en los que participaron el Comité de correlación del Código de seguridad de ASME, la Asociación de ingenieros eléctricos del hierro y el acero, el Museo estadounidense de seguridad, el Comité de estándares de ingeniería estadounidense (AESC) [modificado posteriormente a la Asociación Estadounidense de Estándares (ASA), luego
Due to changes in design, advancement in techniques, and general interest of labor and industry i... more Due to changes in design, advancement in techniques, and general interest of labor and industry in safety, the Sectional Committee, under the joint sponsorship ofASME and the Bureau ofYards and Docks (now the Naval Facilities Engineering Command), was reorganized on January 31, 1962, with 39 members representing 27 national organizations. The new committee changed the format of ASA B30.2-1943 so that the multitude of equipment types it addressed could be published in separate volumes that could completely cover the construction, installation, inspection, testing, maintenance, and operation of each type of equipment that was included in the scope of ASA B30.2. This format change resulted in the initial publication of B30.3, B30.5, B30.6, B30.11, and B30.16 being designated as "Revisions" of B30.2 with the remainder ofthe B30 volumes being published as totally new volumes. ASA changed its name to USASI in 1966 and to ANSI in 1969, which resulted in B30 volumes from 1943 to 1968 being designated as "ASA B30," "USAS B30" or "ANSI B30" depending on their date of publication. In 1982, the committee was reorganized as an Accredited Organization Committee, operating under procedures developed by ASME and accredited by ANSI. This Standard presents a coordinated set of rules that may serve as a guide to government and other regulatory bodies and municipal authorities responsible for the guarding and inspection of the equipment falling within its scope. The suggestions leading to accident prevention are given as both mandatory and advisory provisions; compliance with both types may be required by employers of their employees. In case ofpractical difficulties, new developments, or unnecessary hardship, the administrative or regulatory authority may grant variances from the literal requirements or permit the use ofother devices or methods, but only when it is clearly evident that an equivalent degree of protection is thereby secured. To secure uniform application and interpretation of this Standard, administrative or regulatory authorities are urged to consult the B30 Committee in accordance with the format described in Section IX of the B30 Standard Introduction, before rendering decisions on disputed points. Safety codes and standards are intended to enhance public safety. Revisions result from committee consideration of factors such as technological advances, new data, and changing environmental and industry needs. Revisions do not imply that previous editions were inadequate. The ASME B30.5-2007 edition added responsibilities to be assigned in the worksite organization. The 2011 edition included minor revisions and the addition of Nonmandatory Appendix A on critical lifts. The 2014 edition incorporated many global B30 changes including the addition of personnel competence and translation requirements as well as other revisions made throughout the document. This 2018 edition revises the Crane Operation in the Vicinity of Electric Power Lines section entirely, adds a new section on Rigger Responsibilities, and incorporates other miscellaneous revisions. This edition of the B30.5 Volume was approved by the B30 Committee and by ASME, and was approved by ANSI and designated as an American National Standard on
Due to changes in design, advancement in techniques, and general interest of labor and industry i... more Due to changes in design, advancement in techniques, and general interest of labor and industry in safety, the Sectional Committee, under the joint sponsorship of ASME and the Bureau of Yards and Docks (now the Naval Facilities Engineering Command), was reorganized on January 31, 1962, with 39 members representing 27 national organizations. The new Committee changed the format of ASA B30.2-1943 so that the multitude of equipment types it addressed could be published in separate volumes that could completely cover the construction, installation, inspection, testing, maintenance, and operation of each type of equipment that was included in the scope of ASA B30.2. This format change resulted in B30.3, B30.5, B30.6, B30.11, and B30.16 being initially published as "Revisions" of B30.2, with the remainder of the B30 volumes being published as totally new volumes. ASA changed its name to USASI in 1966 and to ANSI in 1969, which resulted in B30 volumes from 1943 to 1968 being designated as ASA B30, USAS B30, or ANSI B30, depending on their date of publication. In 1982, the Committee was reorganized as an Accredited Organization Committee operating under procedures developed by ASME and accredited by ANSI. This Standard presents a coordinated set of rules that may serve as a guide to government and other regulatory bodies and municipal authorities responsible for the guarding and inspection of the equipment falling within its scope. The suggestions leading to accident prevention are given both as mandatory and advisory provisions; compliance with both types may be required by employers of their employees. In case of practical difficulties, new developments, or unnecessary hardship, the administrative or regulatory authority may grant variances from the literal requirements or permit the use of other devices or methods, but only when it is clearly evident that an equivalent degree of protection is thereby secured. To secure uniform application and interpretation of this Standard, administrative or regulatory authorities are urged to consult the B30 Committee, in accordance with the format described in Section IX of the B30 Standard Introduction, before rendering decisions on disputed points. Safety codes and standards are intended to enhance public safety. Revisions result from committee consideration of factors such as technological advances, new data, and changing environmental and industry needs. Revisions do not imply that previous editions were inadequate.
The next edition of this Standard is scheduled for publication in 2018. This Standard will become... more The next edition of this Standard is scheduled for publication in 2018. This Standard will become effective 1 year after the Date of Issuance. ASME issues written replies to inquiries concerning interpretations of technical aspects of this Standard. Interpretations are published on the ASME Web site under the Committee Pages at http://cstools.asme.org/ as they are issued. Interpretations will also be included with each edition. Errata to codes and standards may be posted on the ASME Web site under the Committee Pages to provide corrections to incorrectly published items, or to correct typographical or grammatical errors in codes and standards. Such errata shall be used on the date posted. The Committee Pages can be found at http://cstools.asme.org/. There is an option available to automatically receive an e-mail notification when errata are posted to a particular code or standard. This option can be found on the appropriate Committee Page after selecting "Errata" in the "Publication Information" section. ASME is the registered trademark of The American Society of Mechanical Engineers. This code or standard was developed under procedures accredited as meeting the criteria for American National Standards. The Standards Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate. The proposed code or standard was made available for public review and comment that provides an opportunity for additional public input from industry, academia, regulatory agencies, and the public-at-large. ASME does not "approve," "rate," or "endorse" any item, construction, proprietary device, or activity. ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable letters patent, nor assumes any such liability. Users of a code or standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard. ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME procedures and policies, which precludes the issuance of interpretations by individuals. No part of this document may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher.
fue presentado a la reunión anual de ASME. Las reuniones y discusiones relacionadas a la segurida... more fue presentado a la reunión anual de ASME. Las reuniones y discusiones relacionadas a la seguridad de las grúas, grúas de brazo móvil y winches se celebraron desde 1920 hasta 1925, con la participación del
y un grupo de empresas vascas especializadas en este tipo de trabajos por establecer un procedimi... more y un grupo de empresas vascas especializadas en este tipo de trabajos por establecer un procedimiento y unas medidas preventivas para que las labores que se realizan en este sector cumplan los requisitos de seguridad y salud laboral necesarios. Con esta inquietud se formó un grupo de especialistas provenientes de empresas de estabilización de taludes, alquiladoras de gruas, Coordinación de Seguridad y Salud, Servicios de Prevención y los propios técnicos de OSALAN, para dar respuesta a la problemática de seguridad que tradicionalmente se ha presentado en la realización de estos trabajos y que, por sus riesgos, merecen un especial tratamiento. Fruto de este proceso de trabajo es esta guía que tiene por objetivo servir de herramienta útil tanto a las empresas como a los propios técnicos del ramo. Para confeccionar esta guía, se ha partido de una evaluación de riesgos (incluida al final de la misma) que ha servido de base para la redacción de un Procedimiento de Trabajo, que se completa con un "chek list". Considero que es un reto para todos conseguir la implantación de este procedimiento que se convertirá en un primer y muy importante paso para minimizar los riesgos de una actividad que sigue sin ser contemplada en la mayor parte de los proyectos de ejecución de las obras. En este sentido, espero que esta Guía se convierta en una herramienta de gran valor práctico.
La norma B30.1 se aplica a gatos de propósito general y portátil de las siguientes categorías: Ga... more La norma B30.1 se aplica a gatos de propósito general y portátil de las siguientes categorías: Gatos hidráulicos manuales o motorizados, gatos mecánicos de trinquete, y martinetes manuales o mecánicos de accionamiento eléctrico. Gatos diseñados para servicio automotriz, trip-lowered jacks, y los que son una parte integral de otros equipos NO están incluidos en el alcance de esta Norma. Los dispositivos diseñados para el soporte estático en lugar de levantar no están incluidos.
Grúas móviles y sobre riel (de vía) Normas de seguridad para cablecarriles, grúas, derricks (cabr... more Grúas móviles y sobre riel (de vía) Normas de seguridad para cablecarriles, grúas, derricks (cabrias), elevadores, ganchos, gatos y eslingas UNA NORMA NACIONAL AMERICANA ASME B30.5-2007 (Revisión de ASME B30.5-2004) ii Fecha de emisión: 7 de marzo de 2008 La publicación de la próxima edición de esta Norma está prevista para el 2010. No habrá addenda para esta edición. ASME responde por escrito a las preguntas relativas a la interpretación de los aspectos técnicos de la presente Norma. Las interpretaciones son publicadas en el sitio Web de ASME en el marco del Committee Pages, en http://cstools.asme.org/ a medida que se emiten y también se publicarán en la próxima edición de la Norma.
The next edition of this Standard is scheduled for publication in 2018. This Standard will become... more The next edition of this Standard is scheduled for publication in 2018. This Standard will become effective 1 year after the Date of Issuance. ASME issues written replies to inquiries concerning interpretations of technical aspects of this Standard. Interpretations are published on the ASME Web site under the Committee Pages at http://cstools.asme.org/ as they are issued. Interpretations will also be included with each edition. Errata to codes and standards may be posted on the ASME Web site under the Committee Pages to provide corrections to incorrectly published items, or to correct typographical or grammatical errors in codes and standards. Such errata shall be used on the date posted. The Committee Pages can be found at http://cstools.asme.org/. There is an option available to automatically receive an e-mail notification when errata are posted to a particular code or standard. This option can be found on the appropriate Committee Page after selecting "Errata" in the "Publication Information" section. ASME is the registered trademark of The American Society of Mechanical Engineers. This code or standard was developed under procedures accredited as meeting the criteria for American National Standards. The Standards Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate. The proposed code or standard was made available for public review and comment that provides an opportunity for additional public input from industry, academia, regulatory agencies, and the public-at-large. ASME does not "approve," "rate," or "endorse" any item, construction, proprietary device, or activity. ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable letters patent, nor assumes any such liability. Users of a code or standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard. ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME procedures and policies, which precludes the issuance of interpretations by individuals. No part of this document may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher.
Uploads
Papers by Claudio Godoy