Close
0%
0%

Joe Selvik

Software Engineer and Co-Founder of FixturFab.com

Denver
Following
Send a private message
Similar accounts worth following
2 Followers
37 Following
0 Projects
joe-selvik
Send a private message

This user joined on 04/15/2020.

338k
8.8k
217
675
Small and simple software for plotting data from serial port
Project Owner Contributor

SerialPlot - Realtime Plotting Software

hasan-yavuz-zderyaHasan Yavuz Özderya

117.9k
1,540.8k
75
2.5k
Follow for the 'Hacklet' and latest news about hackaday.io
Project Owner Contributor

Hackaday.io Project

lutetiumLutetium

96.4k
524
12
193
A piezo inkjet printer built from scratch
Project Owner Contributor

DIY Inkjet Printer

dominik-meffertDominik Meffert

48k
10.6k
28
90
A project about Home Automation. I want to replace my old thermostat with an IoT ESP8266 + OLED 128x64 Screen + OpenHab + MQTT + Micropython
Project Owner Contributor

Home automation: thermostat with ESP8266 & OpenHab

jorgeJorge

35.3k
7.7k
30
193
An Off-the-grid messaging system.
Project Owner Contributor

Skrypt

taiwoTaiwo

31.5k
2.3k
1
40
Portable electronic device to measure air and noise pollution
Project Owner Contributor

Street Sense

mike-teachmanMike Teachman

28.8k
12.5k
8
84
Creating home automation sensors and controllers that can be used around the house forming a mesh network for communication
Project Owner Contributor

Home automation using RF mesh network and arduino

lewisLewis

22.8k
2.4k
10
69
From raw RF samples of the GPS L1 C/A signal to a position fix, in a completely open fashion
Project Owner Contributor

Full Stack GPS Receiver

mike-hamster-fieldMike "Hamster" Field

17.1k
13.7k
14
29
This open-source, low-power LTE shield uses cutting-edge CAT-M technology and also integrates GNSS location capabilities!
Project Owner Contributor

LTE CAT-M1/NB-IoT Shield for Arduino

timothy-wooTimothy Woo

16.5k
2.2k
10
188
This is a design for a low-cost extruder for printing objects directly from recycled plastic flakes instead of using filament.
Project Owner Contributor

Trash Printer - Recycled Plastic 3D Print Head

sam-smithSam Smith

15.6k
10.3k
3
32
Interfacing 3.5" HD 1.44 MB Floppy drive through FDD connector with Arduino UNO
Project Owner Contributor

Arduino raw data 3.5" Floppy reader

lukas-vacekLukas Vacek

13.7k
14.9k
4
38
Autonomous intelligent IOT nodes connected to the home network, controlled via simple IFTTT style rules, configured via web interface
Project Owner Contributor

WiFi Based Distributed IOT Home Automation

andreyAndrey

12.9k
9.4k
19
70
A robot to sail around the world alone
Project Owner Contributor

Ladon Project

pierce-nicholsPierce Nichols

12.9k
7.4k
2
31
Too simple for a project page & which may never happen.
Project Owner Contributor

Silly hardware wishlist

lion-mclionheadlion mclionhead

12.6k
87
17
106
I have trained wild magpies in my Garden to trade litter for food! The whole project relies on mechanical design, electronics, software and
Project Owner Contributor

BirdBox

hfor62hfor62

11.7k
2.1k
8
60
Active mixing, fused filament fabrication 3D printer.
Project Owner Contributor

Arcus-3D-M2 - Mixed material filament printer

masterofnullMasterOfNull

10.8k
1.1k
0
22
Use a Raspberry Pi to build an EV charging station
Project Owner Contributor

Raspberry Pi EVSE Hat

nick-sayerNick Sayer

9.1k
1.2k
2
11
Using a port of ChibiOS for the Teensy 3 series, my goal is to run it on Teensy 3.6.
Project Owner Contributor

ChibiOS on Teensy 3.6

doctekdoctek

View all

Share this profile

Share

Bits

Send a private message to Joe Selvik

Become cool instantly

Create your Hackaday.io profile like Joe Selvik and many others

Report user as inappropriate

You are about to report the user "Joe Selvik", please tell us the reason.