NAS-104368 / 22.02.1 / Set of patches to split NTB resources between several drivers.#31
Merged
Conversation
Without this it was impossible to use multple NTB consumer drivers, since kernel just attached the first one to all NTBs. This replicates driver_override device attribute from PCI, plus adds module parameter to ease default setting.
Previously ntb_transport required at least 6 scratchpad registers, plus 2 more for each additional memory window. That is too much for some configurations, where several drivers have to share resources of the same NTB hardware. This patch introduces new compact version of the protocol, requiring only 3 scratchpad registers, plus one more for each additional memory window. The optimization is based on fact that neither of version, number of windows or number of queue pairs really need more then one byte each, and window sizes of 4GB are not very useful now. The new protocol is activated automatically when the configuration is low on scratchpad registers, or it can be activated explicitly with module parameter.
The hack is no longer needed with ntb_split introduction. This reverts commit 5030d63.
It attaches as client to some NTB device and provides several other NTB device, splitting NTB resources according to config module parameter. For example, one BAR can be dedicated for remote memory access, while other resources can be used for packet transport for virtual Ethernet interface.
bugclerk
changed the title
rick-mesta
approved these changes
Apr 4, 2022
umsaleem
pushed a commit
that referenced
this pull request
Mar 4, 2024
[ Upstream commit a7d6027 ] syzkaller reported an overflown write in arp_req_get(). [0] When ioctl(SIOCGARP) is issued, arp_req_get() looks up an neighbour entry and copies neigh->ha to struct arpreq.arp_ha.sa_data. The arp_ha here is struct sockaddr, not struct sockaddr_storage, so the sa_data buffer is just 14 bytes. In the splat below, 2 bytes are overflown to the next int field, arp_flags. We initialise the field just after the memcpy(), so it's not a problem. However, when dev->addr_len is greater than 22 (e.g. MAX_ADDR_LEN), arp_netmask is overwritten, which could be set as htonl(0xFFFFFFFFUL) in arp_ioctl() before calling arp_req_get(). To avoid the overflow, let's limit the max length of memcpy(). Note that commit b5f0de6 ("net: dev: Convert sa_data to flexible array in struct sockaddr") just silenced syzkaller. [0]: memcpy: detected field-spanning write (size 16) of single field "r->arp_ha.sa_data" at net/ipv4/arp.c:1128 (size 14) WARNING: CPU: 0 PID: 144638 at net/ipv4/arp.c:1128 arp_req_get+0x411/0x4a0 net/ipv4/arp.c:1128 Modules linked in: CPU: 0 PID: 144638 Comm: syz-executor.4 Not tainted 6.1.74 #31 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-debian-1.16.0-5 04/01/2014 RIP: 0010:arp_req_get+0x411/0x4a0 net/ipv4/arp.c:1128 Code: fd ff ff e8 41 42 de fb b9 0e 00 00 00 4c 89 fe 48 c7 c2 20 6d ab 87 48 c7 c7 80 6d ab 87 c6 05 25 af 72 04 01 e8 5f 8d ad fb <0f> 0b e9 6c fd ff ff e8 13 42 de fb be 03 00 00 00 4c 89 e7 e8 a6 RSP: 0018:ffffc900050b7998 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff88803a815000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffffffff8641a44a RDI: 0000000000000001 RBP: ffffc900050b7a98 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000000 R11: 203a7970636d656d R12: ffff888039c54000 R13: 1ffff92000a16f37 R14: ffff88803a815084 R15: 0000000000000010 FS: 00007f172bf306c0(0000) GS:ffff88805aa00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f172b3569f0 CR3: 0000000057f12005 CR4: 0000000000770ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> arp_ioctl+0x33f/0x4b0 net/ipv4/arp.c:1261 inet_ioctl+0x314/0x3a0 net/ipv4/af_inet.c:981 sock_do_ioctl+0xdf/0x260 net/socket.c:1204 sock_ioctl+0x3ef/0x650 net/socket.c:1321 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:870 [inline] __se_sys_ioctl fs/ioctl.c:856 [inline] __x64_sys_ioctl+0x18e/0x220 fs/ioctl.c:856 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x37/0x90 arch/x86/entry/common.c:81 entry_SYSCALL_64_after_hwframe+0x64/0xce RIP: 0033:0x7f172b262b8d Code: 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f172bf300b8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00007f172b3abf80 RCX: 00007f172b262b8d RDX: 0000000020000000 RSI: 0000000000008954 RDI: 0000000000000003 RBP: 00007f172b2d3493 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 000000000000000b R14: 00007f172b3abf80 R15: 00007f172bf10000 </TASK> Reported-by: syzkaller <[email protected]> Reported-by: Bjoern Doebel <[email protected]> Fixes: 1da177e ("Linux-2.6.12-rc2") Signed-off-by: Kuniyuki Iwashima <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Paolo Abeni <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
umsaleem
pushed a commit
that referenced
this pull request
May 1, 2024
commit a7d6027 upstream. syzkaller reported an overflown write in arp_req_get(). [0] When ioctl(SIOCGARP) is issued, arp_req_get() looks up an neighbour entry and copies neigh->ha to struct arpreq.arp_ha.sa_data. The arp_ha here is struct sockaddr, not struct sockaddr_storage, so the sa_data buffer is just 14 bytes. In the splat below, 2 bytes are overflown to the next int field, arp_flags. We initialise the field just after the memcpy(), so it's not a problem. However, when dev->addr_len is greater than 22 (e.g. MAX_ADDR_LEN), arp_netmask is overwritten, which could be set as htonl(0xFFFFFFFFUL) in arp_ioctl() before calling arp_req_get(). To avoid the overflow, let's limit the max length of memcpy(). Note that commit b5f0de6 ("net: dev: Convert sa_data to flexible array in struct sockaddr") just silenced syzkaller. [0]: memcpy: detected field-spanning write (size 16) of single field "r->arp_ha.sa_data" at net/ipv4/arp.c:1128 (size 14) WARNING: CPU: 0 PID: 144638 at net/ipv4/arp.c:1128 arp_req_get+0x411/0x4a0 net/ipv4/arp.c:1128 Modules linked in: CPU: 0 PID: 144638 Comm: syz-executor.4 Not tainted 6.1.74 #31 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-debian-1.16.0-5 04/01/2014 RIP: 0010:arp_req_get+0x411/0x4a0 net/ipv4/arp.c:1128 Code: fd ff ff e8 41 42 de fb b9 0e 00 00 00 4c 89 fe 48 c7 c2 20 6d ab 87 48 c7 c7 80 6d ab 87 c6 05 25 af 72 04 01 e8 5f 8d ad fb <0f> 0b e9 6c fd ff ff e8 13 42 de fb be 03 00 00 00 4c 89 e7 e8 a6 RSP: 0018:ffffc900050b7998 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff88803a815000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffffffff8641a44a RDI: 0000000000000001 RBP: ffffc900050b7a98 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000000 R11: 203a7970636d656d R12: ffff888039c54000 R13: 1ffff92000a16f37 R14: ffff88803a815084 R15: 0000000000000010 FS: 00007f172bf306c0(0000) GS:ffff88805aa00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f172b3569f0 CR3: 0000000057f12005 CR4: 0000000000770ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> arp_ioctl+0x33f/0x4b0 net/ipv4/arp.c:1261 inet_ioctl+0x314/0x3a0 net/ipv4/af_inet.c:981 sock_do_ioctl+0xdf/0x260 net/socket.c:1204 sock_ioctl+0x3ef/0x650 net/socket.c:1321 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:870 [inline] __se_sys_ioctl fs/ioctl.c:856 [inline] __x64_sys_ioctl+0x18e/0x220 fs/ioctl.c:856 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x37/0x90 arch/x86/entry/common.c:81 entry_SYSCALL_64_after_hwframe+0x64/0xce RIP: 0033:0x7f172b262b8d Code: 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f172bf300b8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00007f172b3abf80 RCX: 00007f172b262b8d RDX: 0000000020000000 RSI: 0000000000008954 RDI: 0000000000000003 RBP: 00007f172b2d3493 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 000000000000000b R14: 00007f172b3abf80 R15: 00007f172bf10000 </TASK> Reported-by: syzkaller <[email protected]> Reported-by: Bjoern Doebel <[email protected]> Fixes: 1da177e ("Linux-2.6.12-rc2") Signed-off-by: Kuniyuki Iwashima <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Paolo Abeni <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
wongsyrone
pushed a commit
to wongsyrone/truenas-scale-linux
that referenced
this pull request
Dec 9, 2024
[ Upstream commit d4f36e5 ] Running "modprobe amdgpu" the second time (followed by a modprobe -r amdgpu) causes a call trace like: [ 845.212163] Memory manager not clean during takedown. [ 845.212170] WARNING: CPU: 4 PID: 2481 at drivers/gpu/drm/drm_mm.c:999 drm_mm_takedown+0x2b/0x40 [ 845.212177] Modules linked in: amdgpu(OE-) amddrm_ttm_helper(OE) amddrm_buddy(OE) amdxcp(OE) amd_sched(OE) drm_exec drm_suballoc_helper drm_display_helper i2c_algo_bit amdttm(OE) amdkcl(OE) cec rc_core sunrpc qrtr intel_rapl_msr intel_rapl_common snd_hda_codec_hdmi edac_mce_amd snd_hda_intel snd_intel_dspcfg snd_intel_sdw_acpi snd_usb_audio snd_hda_codec snd_usbmidi_lib kvm_amd snd_hda_core snd_ump mc snd_hwdep kvm snd_pcm snd_seq_midi snd_seq_midi_event irqbypass crct10dif_pclmul snd_rawmidi polyval_clmulni polyval_generic ghash_clmulni_intel sha256_ssse3 sha1_ssse3 snd_seq aesni_intel crypto_simd snd_seq_device cryptd snd_timer mfd_aaeon asus_nb_wmi eeepc_wmi joydev asus_wmi snd ledtrig_audio sparse_keymap ccp wmi_bmof input_leds k10temp i2c_piix4 platform_profile rapl soundcore gpio_amdpt mac_hid binfmt_misc msr parport_pc ppdev lp parport efi_pstore nfnetlink dmi_sysfs ip_tables x_tables autofs4 hid_logitech_hidpp hid_logitech_dj hid_generic usbhid hid ahci xhci_pci igc crc32_pclmul libahci xhci_pci_renesas video [ 845.212284] wmi [last unloaded: amddrm_ttm_helper(OE)] [ 845.212290] CPU: 4 PID: 2481 Comm: modprobe Tainted: G W OE 6.8.0-31-generic truenas#31-Ubuntu [ 845.212296] RIP: 0010:drm_mm_takedown+0x2b/0x40 [ 845.212300] Code: 1f 44 00 00 48 8b 47 38 48 83 c7 38 48 39 f8 75 09 31 c0 31 ff e9 90 2e 86 00 55 48 c7 c7 d0 f6 8e 8a 48 89 e5 e8 f5 db 45 ff <0f> 0b 5d 31 c0 31 ff e9 74 2e 86 00 66 0f 1f 84 00 00 00 00 00 90 [ 845.212302] RSP: 0018:ffffb11302127ae0 EFLAGS: 00010246 [ 845.212305] RAX: 0000000000000000 RBX: ffff92aa5020fc08 RCX: 0000000000000000 [ 845.212307] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 [ 845.212309] RBP: ffffb11302127ae0 R08: 0000000000000000 R09: 0000000000000000 [ 845.212310] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000004 [ 845.212312] R13: ffff92aa50200000 R14: ffff92aa5020fb10 R15: ffff92aa5020faa0 [ 845.212313] FS: 0000707dd7c7c080(0000) GS:ffff92b93de00000(0000) knlGS:0000000000000000 [ 845.212316] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 845.212318] CR2: 00007d48b0aee200 CR3: 0000000115a58000 CR4: 0000000000f50ef0 [ 845.212320] PKRU: 55555554 [ 845.212321] Call Trace: [ 845.212323] <TASK> [ 845.212328] ? show_regs+0x6d/0x80 [ 845.212333] ? __warn+0x89/0x160 [ 845.212339] ? drm_mm_takedown+0x2b/0x40 [ 845.212344] ? report_bug+0x17e/0x1b0 [ 845.212350] ? handle_bug+0x51/0xa0 [ 845.212355] ? exc_invalid_op+0x18/0x80 [ 845.212359] ? asm_exc_invalid_op+0x1b/0x20 [ 845.212366] ? drm_mm_takedown+0x2b/0x40 [ 845.212371] amdgpu_gtt_mgr_fini+0xa9/0x130 [amdgpu] [ 845.212645] amdgpu_ttm_fini+0x264/0x340 [amdgpu] [ 845.212770] amdgpu_bo_fini+0x2e/0xc0 [amdgpu] [ 845.212894] gmc_v12_0_sw_fini+0x2a/0x40 [amdgpu] [ 845.213036] amdgpu_device_fini_sw+0x11a/0x590 [amdgpu] [ 845.213159] amdgpu_driver_release_kms+0x16/0x40 [amdgpu] [ 845.213302] devm_drm_dev_init_release+0x5e/0x90 [ 845.213305] devm_action_release+0x12/0x30 [ 845.213308] release_nodes+0x42/0xd0 [ 845.213311] devres_release_all+0x97/0xe0 [ 845.213314] device_unbind_cleanup+0x12/0x80 [ 845.213317] device_release_driver_internal+0x230/0x270 [ 845.213319] ? srso_alias_return_thunk+0x5/0xfbef5 This is caused by lost memory during early init phase. First time driver is removed, memory is freed but when second time the driver is inserted, VBIOS dmub is not active, since the PSP policy is to retain the driver loaded version on subsequent warm boots. Hence, communication with VBIOS DMUB fails. Fix this by aborting further communication with vbios dmub and release the memory immediately. Fixes: f59549c ("drm/amd/display: free bo used for dmub bounding box") Reviewed-by: Rodrigo Siqueira <[email protected]> Signed-off-by: Aurabindo Pillai <[email protected]> Signed-off-by: Rodrigo Siqueira <[email protected]> Tested-by: Daniel Wheeler <[email protected]> Signed-off-by: Alex Deucher <[email protected]> Signed-off-by: Sasha Levin <[email protected]>
yocalebo
pushed a commit
that referenced
this pull request
Aug 22, 2025
…er dereference commit 1bb3363 upstream. A malicious HID device with quirk APPLE_MAGIC_BACKLIGHT can trigger a NULL pointer dereference whilst the power feature-report is toggled and sent to the device in apple_magic_backlight_report_set(). The power feature-report is expected to have two data fields, but if the descriptor declares one field then accessing field[1] and dereferencing it in apple_magic_backlight_report_set() becomes invalid since field[1] will be NULL. An example of a minimal descriptor which can cause the crash is something like the following where the report with ID 3 (power report) only references a single 1-byte field. When hid core parses the descriptor it will encounter the final feature tag, allocate a hid_report (all members of field[] will be zeroed out), create field structure and populate it, increasing the maxfield to 1. The subsequent field[1] access and dereference causes the crash. Usage Page (Vendor Defined 0xFF00) Usage (0x0F) Collection (Application) Report ID (1) Usage (0x01) Logical Minimum (0) Logical Maximum (255) Report Size (8) Report Count (1) Feature (Data,Var,Abs) Usage (0x02) Logical Maximum (32767) Report Size (16) Report Count (1) Feature (Data,Var,Abs) Report ID (3) Usage (0x03) Logical Minimum (0) Logical Maximum (1) Report Size (8) Report Count (1) Feature (Data,Var,Abs) End Collection Here we see the KASAN splat when the kernel dereferences the NULL pointer and crashes: [ 15.164723] Oops: general protection fault, probably for non-canonical address 0xdffffc0000000006: 0000 [#1] SMP KASAN NOPTI [ 15.165691] KASAN: null-ptr-deref in range [0x0000000000000030-0x0000000000000037] [ 15.165691] CPU: 0 UID: 0 PID: 10 Comm: kworker/0:1 Not tainted 6.15.0 #31 PREEMPT(voluntary) [ 15.165691] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/01/2014 [ 15.165691] RIP: 0010:apple_magic_backlight_report_set+0xbf/0x210 [ 15.165691] Call Trace: [ 15.165691] <TASK> [ 15.165691] apple_probe+0x571/0xa20 [ 15.165691] hid_device_probe+0x2e2/0x6f0 [ 15.165691] really_probe+0x1ca/0x5c0 [ 15.165691] __driver_probe_device+0x24f/0x310 [ 15.165691] driver_probe_device+0x4a/0xd0 [ 15.165691] __device_attach_driver+0x169/0x220 [ 15.165691] bus_for_each_drv+0x118/0x1b0 [ 15.165691] __device_attach+0x1d5/0x380 [ 15.165691] device_initial_probe+0x12/0x20 [ 15.165691] bus_probe_device+0x13d/0x180 [ 15.165691] device_add+0xd87/0x1510 [...] To fix this issue we should validate the number of fields that the backlight and power reports have and if they do not have the required number of fields then bail. Fixes: 394ba61 ("HID: apple: Add support for magic keyboard backlight on T2 Macs") Cc: [email protected] Signed-off-by: Qasim Ijaz <[email protected]> Reviewed-by: Orlando Chamberlain <[email protected]> Tested-by: Aditya Garg <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Benjamin Tissoires <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
wongsyrone
pushed a commit
to wongsyrone/truenas-scale-linux
that referenced
this pull request
Feb 14, 2026
commit b4d37cdb77a0015f51fee083598fa227cc07aaf1 upstream. When deassigning a KVM_IRQFD, don't clobber the irqfd's copy of the IRQ's routing entry as doing so breaks kvm_arch_irq_bypass_del_producer() on x86 and arm64, which explicitly look for KVM_IRQ_ROUTING_MSI. Instead, to handle a concurrent routing update, verify that the irqfd is still active before consuming the routing information. As evidenced by the x86 and arm64 bugs, and another bug in kvm_arch_update_irqfd_routing() (see below), clobbering the entry type without notifying arch code is surprising and error prone. As a bonus, checking that the irqfd is active provides a convenient location for documenting _why_ KVM must not consume the routing entry for an irqfd that is in the process of being deassigned: once the irqfd is deleted from the list (which happens *before* the eventfd is detached), it will no longer receive updates via kvm_irq_routing_update(), and so KVM could deliver an event using stale routing information (relative to KVM_SET_GSI_ROUTING returning to userspace). As an even better bonus, explicitly checking for the irqfd being active fixes a similar bug to the one the clobbering is trying to prevent: if an irqfd is deactivated, and then its routing is changed, kvm_irq_routing_update() won't invoke kvm_arch_update_irqfd_routing() (because the irqfd isn't in the list). And so if the irqfd is in bypass mode, IRQs will continue to be posted using the old routing information. As for kvm_arch_irq_bypass_del_producer(), clobbering the routing type results in KVM incorrectly keeping the IRQ in bypass mode, which is especially problematic on AMD as KVM tracks IRQs that are being posted to a vCPU in a list whose lifetime is tied to the irqfd. Without the help of KASAN to detect use-after-free, the most common sympton on AMD is a NULL pointer deref in amd_iommu_update_ga() due to the memory for irqfd structure being re-allocated and zeroed, resulting in irqfd->irq_bypass_data being NULL when read by avic_update_iommu_vcpu_affinity(): BUG: kernel NULL pointer dereference, address: 0000000000000018 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 40cf2b9067 P4D 40cf2b9067 PUD 408362a067 PMD 0 Oops: Oops: 0000 [truenas#1] SMP CPU: 6 UID: 0 PID: 40383 Comm: vfio_irq_test Tainted: G U W O 6.19.0-smp--5dddc257e6b2-irqfd truenas#31 NONE Tainted: [U]=USER, [W]=WARN, [O]=OOT_MODULE Hardware name: Google, Inc. Arcadia_IT_80/Arcadia_IT_80, BIOS 34.78.2-0 09/05/2025 RIP: 0010:amd_iommu_update_ga+0x19/0xe0 Call Trace: <TASK> avic_update_iommu_vcpu_affinity+0x3d/0x90 [kvm_amd] __avic_vcpu_load+0xf4/0x130 [kvm_amd] kvm_arch_vcpu_load+0x89/0x210 [kvm] vcpu_load+0x30/0x40 [kvm] kvm_arch_vcpu_ioctl_run+0x45/0x620 [kvm] kvm_vcpu_ioctl+0x571/0x6a0 [kvm] __se_sys_ioctl+0x6d/0xb0 do_syscall_64+0x6f/0x9d0 entry_SYSCALL_64_after_hwframe+0x4b/0x53 RIP: 0033:0x46893b </TASK> ---[ end trace 0000000000000000 ]--- If AVIC is inhibited when the irfd is deassigned, the bug will manifest as list corruption, e.g. on the next irqfd assignment. list_add corruption. next->prev should be prev (ffff8d474d5cd588), but was 0000000000000000. (next=ffff8d8658f86530). ------------[ cut here ]------------ kernel BUG at lib/list_debug.c:31! Oops: invalid opcode: 0000 [truenas#1] SMP CPU: 128 UID: 0 PID: 80818 Comm: vfio_irq_test Tainted: G U W O 6.19.0-smp--f19dc4d680ba-irqfd truenas#28 NONE Tainted: [U]=USER, [W]=WARN, [O]=OOT_MODULE Hardware name: Google, Inc. Arcadia_IT_80/Arcadia_IT_80, BIOS 34.78.2-0 09/05/2025 RIP: 0010:__list_add_valid_or_report+0x97/0xc0 Call Trace: <TASK> avic_pi_update_irte+0x28e/0x2b0 [kvm_amd] kvm_pi_update_irte+0xbf/0x190 [kvm] kvm_arch_irq_bypass_add_producer+0x72/0x90 [kvm] irq_bypass_register_consumer+0xcd/0x170 [irqbypass] kvm_irqfd+0x4c6/0x540 [kvm] kvm_vm_ioctl+0x118/0x5d0 [kvm] __se_sys_ioctl+0x6d/0xb0 do_syscall_64+0x6f/0x9d0 entry_SYSCALL_64_after_hwframe+0x4b/0x53 </TASK> ---[ end trace 0000000000000000 ]--- On Intel and arm64, the bug is less noisy, as the end result is that the device keeps posting IRQs to the vCPU even after it's been deassigned. Note, the worst of the breakage can be traced back to commit cb21073 ("KVM: Pass new routing entries and irqfd when updating IRTEs"), as before that commit KVM would pull the routing information from the per-VM routing table. But as above, similar bugs have existed since support for IRQ bypass was added. E.g. if a routing change finished before irq_shutdown() invoked kvm_arch_irq_bypass_del_producer(), VMX and SVM would see stale routing information and potentially leave the irqfd in bypass mode. Alternatively, x86 could be fixed by explicitly checking irq_bypass_vcpu instead of irq_entry.type in kvm_arch_irq_bypass_del_producer(), and arm64 could be modified to utilize irq_bypass_vcpu in a similar manner. But (a) that wouldn't fix the routing updates bug, and (b) fixing core code doesn't preclude x86 (or arm64) from adding such code as a sanity check (spoiler alert). Fixes: f70c20a ("KVM: Add an arch specific hooks in 'struct kvm_kernel_irqfd'") Fixes: cb21073 ("KVM: Pass new routing entries and irqfd when updating IRTEs") Fixes: a0d7e2f ("KVM: arm64: vgic-v4: Only attempt vLPI mapping for actual MSIs") Cc: [email protected] Cc: Marc Zyngier <[email protected]> Cc: Oliver Upton <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Sean Christopherson <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
3 participants
Add this suggestion to a batch that can be applied as a single commit.This suggestion is invalid because no changes were made to the code.Suggestions cannot be applied while the pull request is closed.Suggestions cannot be applied while viewing a subset of changes.Only one suggestion per line can be applied in a batch.Add this suggestion to a batch that can be applied as a single commit.Applying suggestions on deleted lines is not supported.You must change the existing code in this line in order to create a valid suggestion.Outdated suggestions cannot be applied.This suggestion has been applied or marked resolved.Suggestions cannot be applied from pending reviews.Suggestions cannot be applied on multi-line comments.Suggestions cannot be applied while the pull request is queued to merge.Suggestion cannot be applied right now. Please check back later.
No description provided.