3D Printed Parts

The controller consists of FDM-printed parts, metal tubes, and M3 screws. It is recommended that the printed part be made from PETG filament rather than PLA filament. PLA is too brittle for frame parts.

Parts for the frame

BOM

• 3x 16mm stainless steel pipe 700mm
• 32x M3 nut
• 32x M3 Washer 7mm
• 12x M3 Bolt 10mm
• 24x M3 Bolt 16mm

Printed parts

• 3x Frame holder - frame_main.step
• 2x Frame Connector - frame_connector.step
• 4x Accessory Holder - frame_accessory_holder.step
• 2x Strap holder optional - strap_holder.step

Rein Sensor

You need to make two of these, only sunshade needs to be mirrored in the slicer software. The left and right parts are identical.

BOM

• 2x M3 Washer 7mm
• 7x M3 Bolt 10mm
• 5x M3 Heatset insert OD 5mm
• 1x 608zz Bearing
• 2.5mm Elastic cord
• Paracord, string etc
• Sponge or some soft foam

Printed parts

• 2x Sunshade(mirror the second one) - sunshade.step
• 2x Sunshade small (optional) - sunshade_small.step
• 1x Flap - flap.step
• 1x Bearing holder - bearing_holder.step
• 1x Bearing collar - bearing_collar.step
• 1x Sensor holder - sensor_holder.step

You need 4x of M3 washers, bolts(10mm) and nuts for connecting one sensor to the accessory holder.

Stirrup Sensor

You need to make two of these, the left and right parts are identical.

BOM

• 1x M3 Bolt 10mm
• 25mm strap
• 25mm strap adjuster

Printed parts

• 1x Stirrup - stirrup.step
• 1x Stirrup plate - stirrup_antislip_holder.step
• 1x Stirrup Reflector - stirrup_reflector_plate.step
• 1x Sunshade (If possible, print from TPU) - sunshade.step
• 1x Sensor holder - sensor_holder.step

You need 4x of M3 washers, bolts(10mm) and nuts for connecting one sensor to the accessory holder.

Nunchuk Connector

BOM

• 2x M3 Bolt 16mm
• 2x M3 Heatset insert OD 5mm
• 3mm zip tie
• 1x "I2C for Wii, WiiChuck Nunchuk Board"

Printed parts

• 1x Lid - nunchuk_connector_lid.step
• 1x Case - nunchuk_connector_body.step
• 1x Holder - nunchuk_connector_holder.step
• 1x Controller holder - nunchuk_controller_holder.step

You need 4x of M3 washers, bolts(10mm) and nuts for connecting the controller holder to the accessory holder.

Electronic Box

Currently there is no PCB design so electronics need to be handwired.

BOM

• 4x M3 Bolt 10mm
• 6x M3 Heatset insert OD 5mm
• 70x50mm Perfboard
• 2x short M3 bolt+washers
• 6x MX compatible keyswitches/keycaps
• Solder, wire etc

Printed parts

• 1x Lid - electronics_box_lid.step
• 1x Case - electronics_box_main_body.step

You need 4x of M3 washers, bolts(10mm) and nuts for connecting the controller holder to the accessory holder.

Miscellaneous

Reins Strap

BOM

• 1 meter faux leather flat strap 15mm
• ~1 meter 3mm paracord

Printed parts

• 2x Strap adapter - strap_adapter.step

Bolt Covers

Printed parts

Works with most of the frame parts.

• Bolt Cover - bolt_cover.step