Merge v4.9.130 into 4.9-2.3.x imx by gibsson · Pull Request #38 · Freescale/linux-fslc

gibsson · 2018-10-02T13:13:34Z

No description provided.

commit ae7304c upstream. Disable interrupts while configuring the transfer and enable them back. We have below as the programming sequence 1. start and slave address 2. byte count and stop In some customer platform there was a lot of interrupts between 1 and 2 and after slave address (around 7 clock cyles) if 2 is not executed then the transaction is nacked. To fix this case make the 2 writes atomic. Signed-off-by: Shubhrajyoti Datta <[email protected]> Signed-off-by: Michal Simek <[email protected]> [wsa: added a newline for better readability] Signed-off-by: Wolfram Sang <[email protected]> Cc: [email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 851a151 upstream. DNV's iTCO is slightly different with SMBCTRL sitting at a different offset when compared to all other devices. Let's fix so that we can properly use iTCO watchdog. Fixes: 84d7f2e ("i2c: i801: Add support for Intel DNV") Cc: <[email protected]> # v4.4+ Signed-off-by: Felipe Balbi <[email protected]> Reviewed-by: Jean Delvare <[email protected]> Signed-off-by: Wolfram Sang <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 204c972 upstream. Copy the key mask to the right offset inside the shadow CRYCB Fixes: bbeaa58 ("KVM: s390: vsie: support aes dea wrapping keys") Signed-off-by: Pierre Morel <[email protected]> Reviewed-by: David Hildenbrand <[email protected]> Reviewed-by: Cornelia Huck <[email protected]> Reviewed-by: Janosch Frank <[email protected]> Cc: [email protected] # v4.8+ Message-Id: <[email protected]> Signed-off-by: Janosch Frank <[email protected]> Signed-off-by: Christian Borntraeger <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 1603764 upstream. On AMD/ATI controllers, the HD-audio controller driver allows a bus reset upon the error recovery, and its procedure includes the cancellation of pending jack polling work as found in snd_hda_bus_codec_reset(). This works usually fine, but it becomes a problem when the reset happens from the jack poll work itself; then calling cancel_work_sync() from the work being processed tries to wait the finish endlessly. As a workaround, this patch adds the check of current_work() and applies the cancel_work_sync() only when it's not from the jackpoll_work. This doesn't fix the root cause of the reported error below, but at least, it eases the unexpected stall of the whole system. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=200937 Cc: <[email protected]> Cc: Lukas Wunner <[email protected]> Signed-off-by: Takashi Iwai <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit b3193bc upstream. In below scenario blkio cgroup does not work as per their assigned weights :- 1. When the underlying device is nonrotational with a single HW queue with depth of >= CFQ_HW_QUEUE_MIN 2. When the use case is forming two blkio cgroups cg1(weight 1000) & cg2(wight 100) and two processes(file1 and file2) doing sync IO in their respective blkio cgroups. For above usecase result of fio (without this patch):- file1: (groupid=0, jobs=1): err= 0: pid=685: Thu Jan 1 19:41:49 1970 write: IOPS=1315, BW=41.1MiB/s (43.1MB/s)(1024MiB/24906msec) <...> file2: (groupid=0, jobs=1): err= 0: pid=686: Thu Jan 1 19:41:49 1970 write: IOPS=1295, BW=40.5MiB/s (42.5MB/s)(1024MiB/25293msec) <...> // both the process BW is equal even though they belong to diff. cgroups with weight of 1000(cg1) and 100(cg2) In above case (for non rotational NCQ devices), as soon as the request from cg1 is completed and even though it is provided with higher set_slice=10, because of CFQ algorithm when the driver tries to fetch the request, CFQ expires this group without providing any idle time nor weight priority and schedules another cfq group (in this case cg2). And thus both cfq groups(cg1 & cg2) keep alternating to get the disk time and hence loses the cgroup weight based scheduling. Below patch gives a chance to cfq algorithm (cfq_arm_slice_timer) to arm the slice timer in case group_idle is enabled. In case if group_idle is also not required (including for nonrotational NCQ drives), we need to explicitly set group_idle = 0 from sysfs for such cases. With this patch result of fio(for above usecase) :- file1: (groupid=0, jobs=1): err= 0: pid=690: Thu Jan 1 00:06:08 1970 write: IOPS=1706, BW=53.3MiB/s (55.9MB/s)(1024MiB/19197msec) <..> file2: (groupid=0, jobs=1): err= 0: pid=691: Thu Jan 1 00:06:08 1970 write: IOPS=1043, BW=32.6MiB/s (34.2MB/s)(1024MiB/31401msec) <..> // In this processes BW is as per their respective cgroups weight. Signed-off-by: Ritesh Harjani <[email protected]> Signed-off-by: Jens Axboe <[email protected]> Signed-off-by: Amit Pundir <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 4d6501d upstream. If a kthread forks (e.g. usermodehelper since commit 1da5c46) but fails in copy_process() between calling dup_task_struct() and setting p->set_child_tid, then the value of p->set_child_tid will be inherited from the parent and get prematurely freed by free_kthread_struct(). kthread() - worker_thread() - process_one_work() | - call_usermodehelper_exec_work() | - kernel_thread() | - _do_fork() | - copy_process() | - dup_task_struct() | - arch_dup_task_struct() | - tsk->set_child_tid = current->set_child_tid // implied | - ... | - goto bad_fork_* | - ... | - free_task(tsk) | - free_kthread_struct(tsk) | - kfree(tsk->set_child_tid) - ... - schedule() - __schedule() - wq_worker_sleeping() - kthread_data(task)->flags // UAF The problem started showing up with commit 1da5c46 since it reused ->set_child_tid for the kthread worker data. A better long-term solution might be to get rid of the ->set_child_tid abuse. The comment in set_kthread_struct() also looks slightly wrong. Debugged-by: Jamie Iles <[email protected]> Fixes: 1da5c46 ("kthread: Make struct kthread kmalloc'ed") Signed-off-by: Vegard Nossum <[email protected]> Acked-by: Oleg Nesterov <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Greg Kroah-Hartman <[email protected]> Cc: Andy Lutomirski <[email protected]> Cc: Frederic Weisbecker <[email protected]> Cc: Jamie Iles <[email protected]> Cc: [email protected] Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Thomas Gleixner <[email protected]> Signed-off-by: Amit Pundir <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit b0f5a8f upstream. This fixes a regression in commit 4d6501d where I didn't notice that MIPS and OpenRISC were reinitialising p->{set,clear}_child_tid to NULL after our initialisation in copy_process(). We can simply get rid of the arch-specific initialisation here since it is now always done in copy_process() before hitting copy_thread{,_tls}(). Review notes: - As far as I can tell, copy_process() is the only user of copy_thread_tls(), which is the only caller of copy_thread() for architectures that don't implement copy_thread_tls(). - After this patch, there is no arch-specific code touching p->set_child_tid or p->clear_child_tid whatsoever. - It may look like MIPS/OpenRISC wanted to always have these fields be NULL, but that's not true, as copy_process() would unconditionally set them again _after_ calling copy_thread_tls() before commit 4d6501d. Fixes: 4d6501d ("kthread: Fix use-after-free if kthread fork fails") Reported-by: Guenter Roeck <[email protected]> Tested-by: Guenter Roeck <[email protected]> # MIPS only Acked-by: Stafford Horne <[email protected]> Acked-by: Oleg Nesterov <[email protected]> Cc: Ralf Baechle <[email protected]> Cc: [email protected] Cc: Jonas Bonn <[email protected]> Cc: Stefan Kristiansson <[email protected]> Cc: [email protected] Cc: Jamie Iles <[email protected]> Cc: Thomas Gleixner <[email protected]> Signed-off-by: Vegard Nossum <[email protected]> Signed-off-by: Linus Torvalds <[email protected]> Signed-off-by: Amit Pundir <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 498c4b4 upstream. The driver may sleep under a spin lock, and the function call path is: rtsx_exclusive_enter_ss (acquire the lock by spin_lock) rtsx_enter_ss rtsx_power_off_card xd_cleanup_work xd_delay_write xd_finish_write xd_copy_page wait_timeout schedule_timeout --> may sleep To fix it, "wait_timeout" is replaced with mdelay in xd_copy_page. Signed-off-by: Jia-Ju Bai <[email protected]> Signed-off-by: Amit Pundir <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 88a5b39 upstream. Noticed by FORTIFY_SOURCE, this swaps memcpy() for strncpy() to zero-value fill the end of the buffer instead of over-reading a string from .rodata. Signed-off-by: Daniel Micay <[email protected]> [kees: wrote commit log] Signed-off-by: Kees Cook <[email protected]> Cc: Greg Kroah-Hartman <[email protected]> Cc: Wayne Porter <[email protected]> Signed-off-by: Amit Pundir <[email protected]>

commit 4c93496 upstream. This fixes a over-read condition detected by FORTIFY_SOURCE for this line: memcpy(SKB_TO_PKT(skb), &ack_pkt, sizeof(skb->cb)); The error was: In file included from ./include/linux/bitmap.h:8:0, from ./include/linux/cpumask.h:11, from ./include/linux/mm_types_task.h:13, from ./include/linux/mm_types.h:4, from ./include/linux/kmemcheck.h:4, from ./include/linux/skbuff.h:18, from drivers/infiniband/sw/rxe/rxe_resp.c:34: In function 'memcpy', inlined from 'send_atomic_ack.constprop' at drivers/infiniband/sw/rxe/rxe_resp.c:998:2, inlined from 'acknowledge' at drivers/infiniband/sw/rxe/rxe_resp.c:1026:3, inlined from 'rxe_responder' at drivers/infiniband/sw/rxe/rxe_resp.c:1286:10: ./include/linux/string.h:309:4: error: call to '__read_overflow2' declared with attribute error: detected read beyond size of object passed as 2nd parameter __read_overflow2(); Daniel Micay noted that struct rxe_pkt_info is 32 bytes on 32-bit architectures, but skb->cb is still 64. The memcpy() over-reads 32 bytes. This fixes it by zeroing the unused bytes in skb->cb. Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Kees Cook <[email protected]> Cc: Moni Shoua <[email protected]> Cc: Doug Ledford <[email protected]> Cc: Sean Hefty <[email protected]> Cc: Daniel Micay <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]> Signed-off-by: Amit Pundir <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit e00f4f4 upstream. blkcg allocates some per-cgroup data structures with GFP_NOWAIT and when that fails falls back to operations which aren't specific to the cgroup. Occassional failures are expected under pressure and falling back to non-cgroup operation is the right thing to do. Unfortunately, I forgot to add __GFP_NOWARN to these allocations and these expected failures end up creating a lot of noise. Add __GFP_NOWARN. Signed-off-by: Tejun Heo <[email protected]> Reported-by: Marc MERLIN <[email protected]> Reported-by: Vlastimil Babka <[email protected]> Signed-off-by: Jens Axboe <[email protected]> Signed-off-by: Amit Pundir <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 265698d upstream. If TX rates are specified during mesh join, the channel must also be specified. Check the channel pointer to avoid a null pointer dereference if it isn't. Reported-by: Jouni Malinen <[email protected]> Fixes: 8564e38 ("cfg80211: add checks for beacon rate, extend to mesh") Signed-off-by: Johannes Berg <[email protected]> Signed-off-by: Amit Pundir <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 9c29c31 upstream. If a spinner is present, there is a chance that the load of rwsem_has_spinner() in rwsem_wake() can be reordered with respect to decrement of rwsem count in __up_write() leading to wakeup being missed: spinning writer up_write caller --------------- ----------------------- [S] osq_unlock() [L] osq spin_lock(wait_lock) sem->count=0xFFFFFFFF00000001 +0xFFFFFFFF00000000 count=sem->count MB sem->count=0xFFFFFFFE00000001 -0xFFFFFFFF00000001 spin_trylock(wait_lock) return rwsem_try_write_lock(count) spin_unlock(wait_lock) schedule() Reordering of atomic_long_sub_return_release() in __up_write() and rwsem_has_spinner() in rwsem_wake() can cause missing of wakeup in up_write() context. In spinning writer, sem->count and local variable count is 0XFFFFFFFE00000001. It would result in rwsem_try_write_lock() failing to acquire rwsem and spinning writer going to sleep in rwsem_down_write_failed(). The smp_rmb() will make sure that the spinner state is consulted after sem->count is updated in up_write context. Signed-off-by: Prateek Sood <[email protected]> Signed-off-by: Peter Zijlstra (Intel) <[email protected]> Cc: Linus Torvalds <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Thomas Gleixner <[email protected]> Cc: [email protected] Cc: [email protected] Cc: [email protected] Cc: [email protected] Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Ingo Molnar <[email protected]> Signed-off-by: Amit Pundir <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 476accb upstream. There is a strange __GFP_NOMEMALLOC usage pattern in SELinux, specifically GFP_ATOMIC | __GFP_NOMEMALLOC which doesn't make much sense. GFP_ATOMIC on its own allows to access memory reserves while __GFP_NOMEMALLOC dictates we cannot use memory reserves. Replace this with the much more sane GFP_NOWAIT in the AVC code as we can tolerate memory allocation failures in that code. Signed-off-by: Michal Hocko <[email protected]> Acked-by: Mel Gorman <[email protected]> Signed-off-by: Paul Moore <[email protected]> Signed-off-by: Amit Pundir <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 50972fe upstream. Fix ordering of link creation between node->prev and prev->next in osq_lock(). A case in which the status of optimistic spin queue is CPU6->CPU2 in which CPU6 has acquired the lock. tail v ,-. <- ,-. |6| |2| `-' -> `-' At this point if CPU0 comes in to acquire osq_lock, it will update the tail count. CPU2 CPU0 ---------------------------------- tail v ,-. <- ,-. ,-. |6| |2| |0| `-' -> `-' `-' After tail count update if CPU2 starts to unqueue itself from optimistic spin queue, it will find an updated tail count with CPU0 and update CPU2 node->next to NULL in osq_wait_next(). unqueue-A tail v ,-. <- ,-. ,-. |6| |2| |0| `-' `-' `-' unqueue-B ->tail != curr && !node->next If reordering of following stores happen then prev->next where prev being CPU2 would be updated to point to CPU0 node: tail v ,-. <- ,-. ,-. |6| |2| |0| `-' `-' -> `-' osq_wait_next() node->next <- 0 xchg(node->next, NULL) tail v ,-. <- ,-. ,-. |6| |2| |0| `-' `-' `-' unqueue-C At this point if next instruction WRITE_ONCE(next->prev, prev); in CPU2 path is committed before the update of CPU0 node->prev = prev then CPU0 node->prev will point to CPU6 node. tail v----------. v ,-. <- ,-. ,-. |6| |2| |0| `-' `-' `-' `----------^ At this point if CPU0 path's node->prev = prev is committed resulting in change of CPU0 prev back to CPU2 node. CPU2 node->next is NULL currently, tail v ,-. <- ,-. <- ,-. |6| |2| |0| `-' `-' `-' `----------^ so if CPU0 gets into unqueue path of osq_lock it will keep spinning in infinite loop as condition prev->next == node will never be true. Signed-off-by: Prateek Sood <[email protected]> [ Added pictures, rewrote comments. ] Signed-off-by: Peter Zijlstra (Intel) <[email protected]> Cc: Linus Torvalds <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Thomas Gleixner <[email protected]> Cc: [email protected] Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Ingo Molnar <[email protected]> Signed-off-by: Amit Pundir <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit c2f8314 upstream. Hillf Danton pointed out that since commit 1d82de6 ("mm, vmscan: make kswapd reclaim in terms of nodes") that PGDAT_WRITEBACK is no longer cleared. It was not noticed as triggering it requires pages under writeback to cycle twice through the LRU and before kswapd gets stalled. Historically, such issues tended to occur on small machines writing heavily to slow storage such as a USB stick. Once kswapd stalls, direct reclaim stalls may be higher but due to the fact that memory pressure is required, it would not be very noticable. Michal Hocko suggested removing the flag entirely but the conservative fix is to restore the intended PGDAT_WRITEBACK behaviour and clear the flag when a suitable zone is balanced. Fixes: 1d82de6 ("mm, vmscan: make kswapd reclaim in terms of nodes") Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Mel Gorman <[email protected]> Acked-by: Johannes Weiner <[email protected]> Acked-by: Michal Hocko <[email protected]> Acked-by: Hillf Danton <[email protected]> Cc: Minchan Kim <[email protected]> Cc: Rik van Riel <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]> Signed-off-by: Amit Pundir <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

…ating commit 047d72c upstream. Commit 1d82de6 ("mm, vmscan: make kswapd reclaim in terms of nodes") allowed laptop_mode=1 to start writing not just when the priority drops to DEF_PRIORITY - 2 but also when the node is unreclaimable. That appears to be a spurious change in this patch as I doubt the series was tested with laptop_mode, and neither is that particular change mentioned in the changelog. Remove it, it's still recent. Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Johannes Weiner <[email protected]> Acked-by: Hillf Danton <[email protected]> Acked-by: Mel Gorman <[email protected]> Acked-by: Michal Hocko <[email protected]> Cc: Jia He <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]> Signed-off-by: Amit Pundir <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit c83532f upstream. SWAP support on ARC was fixed earlier by commit 6e37611 ("ARC: Fix CONFIG_SWAP") so now we may safely enable it on platforms that have external media like USB and SD-card. Note: it was already allowed for HSDK Signed-off-by: Alexey Brodkin <[email protected]> Cc: [email protected] # 6e37611: ARC: Fix CONFIG_SWAP Signed-off-by: Vineet Gupta <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit a39284a ] There are only 2 callers of scif_get_new_port() and both appear to get the error handling wrong. Both treat zero returns as error, but it actually returns negative error codes and >= 0 on success. Fixes: e9089f4 ("misc: mic: SCIF open close bind and listen APIs") Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit d89d415 ] Android's header sanitization tool chokes on static inline functions having a trailing semicolon, leading to an incorrectly parsed header file. While the tool should obviously be fixed, also fix the header files for the two affected functions: ethtool_get_flow_spec_ring() and ethtool_get_flow_spec_ring_vf(). Fixes: 8cf6f49 ("ethtool: Add helper routines to pass vf to rx_flow_spec") Reporetd-by: Blair Prescott <[email protected]> Signed-off-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 6c3711e ] This driver was recently updated to use serdev, so add the appropriate dependency. Without this one can get compiler warnings like this if CONFIG_SERIAL_DEV_BUS is not enabled: CC [M] drivers/bluetooth/hci_h5.o drivers/bluetooth/hci_h5.c:934:36: warning: ‘h5_serdev_driver’ defined but not used [-Wunused-variable] static struct serdev_device_driver h5_serdev_driver = { ^~~~~~~~~~~~~~~~ Signed-off-by: Johan Hedberg <[email protected]> Signed-off-by: Marcel Holtmann <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 40b25bc ] There is a bug in regards to deferred probing within the drivers core that causes GPIO-driver to suspend after its users. The bug appears if GPIO-driver probe is getting deferred, which happens after introducing dependency on PINCTRL-driver for the GPIO-driver by defining "gpio-ranges" property in device-tree. The bug in the drivers core is old (more than 4 years now) and is well known, unfortunately there is no easy fix for it. The good news is that we can workaround the deferred probe issue by changing GPIO / PINCTRL drivers registration order and hence by moving PINCTRL driver registration to the arch_init level and GPIO to the subsys_init. Signed-off-by: Dmitry Osipenko <[email protected]> Acked-by: Stefan Agner <[email protected]> Signed-off-by: Linus Walleij <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 77fefa9 ] Modify the register offsets in the Broadcom iProc mdio mux to start from the top of the register address space. Earlier, the base address pointed to the end of the block's register space. The base address will now point to the start of the mdio's address space. The offsets have been fixed to match this. Signed-off-by: Arun Parameswaran <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Reviewed-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 6a64f6e ] When __transport_register_session is called from transport_register_session irqs will already have been disabled, so we do not want the unlock irq call to enable them until the higher level has done the final spin_unlock_irqrestore/ spin_unlock_irq. This has __transport_register_session use the save/restore call. Signed-off-by: Mike Christie <[email protected]> Reviewed-by: Bart Van Assche <[email protected]> Reviewed-by: Christoph Hellwig <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit d63e2fc ] During raid5 replacement, the stripes can be marked with R5_NeedReplace flag. Data can be read from being-replaced devices and written to replacing spares without reading all other devices. (It's 'replace' mode. s.replacing = 1) If a being-replaced device is dropped, the replacement progress will be interrupted and resumed with pure recovery mode. However, existing stripes before being interrupted cannot read from the dropped device anymore. It prints lots of WARN_ON messages. And it results in data corruption because existing stripes write problematic data into its replacement device and update the progress. \# Erase disks (1MB + 2GB) dd if=/dev/zero of=/dev/sda bs=1MB count=2049 dd if=/dev/zero of=/dev/sdb bs=1MB count=2049 dd if=/dev/zero of=/dev/sdc bs=1MB count=2049 dd if=/dev/zero of=/dev/sdd bs=1MB count=2049 mdadm -C /dev/md0 -amd -R -l5 -n3 -x0 /dev/sd[abc] -z 2097152 \# Ensure array stores non-zero data dd if=/root/data_4GB.iso of=/dev/md0 bs=1MB \# Start replacement mdadm /dev/md0 -a /dev/sdd mdadm /dev/md0 --replace /dev/sda Then, Hot-plug out /dev/sda during recovery, and wait for recovery done. echo check > /sys/block/md0/md/sync_action cat /sys/block/md0/md/mismatch_cnt # it will be greater than 0. Soon after you hot-plug out /dev/sda, you will see many WARN_ON messages. The replacement recovery will be interrupted shortly. After the recovery finishes, it will result in data corruption. Actually, it's just an unhandled case of replacement. In commit <f94c0b6658c7> (md/raid5: fix interaction of 'replace' and 'recovery'.), if a NeedReplace device is not UPTODATE then that is an error, the commit just simply print WARN_ON but also mark these corrupted stripes with R5_WantReplace. (it means it's ready for writes.) To fix this case, we can leverage 'sync and replace' mode mentioned in commit <9a3e1101b827> (md/raid5: detect and handle replacements during recovery.). We can add logics to detect and use 'sync and replace' mode for these stripes. Reported-by: Alex Chen <[email protected]> Reviewed-by: Alex Wu <[email protected]> Reviewed-by: Chung-Chiang Cheng <[email protected]> Signed-off-by: BingJing Chang <[email protected]> Signed-off-by: Shaohua Li <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 363e934 ] timer_base::must_forward_clock is indicating that the base clock might be stale due to a long idle sleep. The forwarding of the base clock takes place in the timer softirq or when a timer is enqueued to a base which is idle. If the enqueue of timer to an idle base happens from a remote CPU, then the following race can happen: CPU0 CPU1 run_timer_softirq mod_timer base = lock_timer_base(timer); base->must_forward_clk = false if (base->must_forward_clk) forward(base); -> skipped enqueue_timer(base, timer, idx); -> idx is calculated high due to stale base unlock_timer_base(timer); base = lock_timer_base(timer); forward(base); The root cause is that timer_base::must_forward_clk is cleared outside the timer_base::lock held region, so the remote queuing CPU observes it as cleared, but the base clock is still stale. This can cause large granularity values for timers, i.e. the accuracy of the expiry time suffers. Prevent this by clearing the flag with timer_base::lock held, so that the forwarding takes place before the cleared flag is observable by a remote CPU. Signed-off-by: Gaurav Kohli <[email protected]> Signed-off-by: Thomas Gleixner <[email protected]> Cc: [email protected] Cc: [email protected] Cc: [email protected] Link: https://lkml.kernel.org/r/[email protected] Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 81ae962 ] Free resources instead of direct return of the error code if kim_probe fails. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Anton Vasilyev <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit f019f07 ] The uio_unregister_device() function assumes that if "info->uio_dev" is non-NULL that means "info" is fully allocated. Setting info->uio_de has to be the last thing in the function. In the current code, if request_threaded_irq() fails then we return with info->uio_dev set to non-NULL but info is not fully allocated and it can lead to double frees. Fixes: beafc54 ("UIO: Add the User IO core code") Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 0419056 ] If number of isa and pci boards exceed NUM_BOARDS on the path rp_init()->init_PCI()->register_PCI() then buffer overwrite occurs in register_PCI() on assign rcktpt_io_addr[i]. The patch adds check on upper bound for index of registered board in register_PCI. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Anton Vasilyev <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 3611ce9 ] For the case when sbi->segs_per_sec > 1, take section:segment = 5 for example, if segment 1 is just used and allocate new segment 2, and the blocks of segment 1 is invalidated, at this time, the previous code will use __set_test_and_free to free the free_secmap and free_sections++, this is not correct since it is still a current section, so fix it. Signed-off-by: Yunlong Song <[email protected]> Reviewed-by: Chao Yu <[email protected]> Signed-off-by: Jaegeuk Kim <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit fe18d64 upstream. Marking mmp bh dirty before writing it will make writeback pick up mmp block later and submit a write, we don't want the duplicate write as kmmpd thread should have full control of reading and writing the mmp block. Another reason is we will also have random I/O error on the writeback request when blk integrity is enabled, because kmmpd could modify the content of the mmp block(e.g. setting new seq and time) while the mmp block is under I/O requested by writeback. Signed-off-by: Li Dongyang <[email protected]> Signed-off-by: Theodore Ts'o <[email protected]> Reviewed-by: Andreas Dilger <[email protected]> Cc: [email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 338affb upstream. When in effect, add "test_dummy_encryption" to _ext4_show_options() so that it is shown in /proc/mounts and other relevant procfs files. Signed-off-by: Eric Biggers <[email protected]> Signed-off-by: Theodore Ts'o <[email protected]> Cc: [email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit d0cdb3c upstream. When a task which previously ran on a given CPU is remotely queued to wake up on that same CPU, there is a period where the task's state is TASK_WAKING and its vruntime is not normalized. This is not accounted for in vruntime_normalized() which will cause an error in the task's vruntime if it is switched from the fair class during this time. For example if it is boosted to RT priority via rt_mutex_setprio(), rq->min_vruntime will not be subtracted from the task's vruntime but it will be added again when the task returns to the fair class. The task's vruntime will have been erroneously doubled and the effective priority of the task will be reduced. Note this will also lead to inflation of all vruntimes since the doubled vruntime value will become the rq's min_vruntime when other tasks leave the rq. This leads to repeated doubling of the vruntime and priority penalty. Fix this by recognizing a WAKING task's vruntime as normalized only if sched_remote_wakeup is true. This indicates a migration, in which case the vruntime would have been normalized in migrate_task_rq_fair(). Based on a similar patch from John Dias <[email protected]>. Suggested-by: Peter Zijlstra <[email protected]> Tested-by: Dietmar Eggemann <[email protected]> Signed-off-by: Steve Muckle <[email protected]> Signed-off-by: Peter Zijlstra (Intel) <[email protected]> Cc: Chris Redpath <[email protected]> Cc: John Dias <[email protected]> Cc: Linus Torvalds <[email protected]> Cc: Miguel de Dios <[email protected]> Cc: Morten Rasmussen <[email protected]> Cc: Patrick Bellasi <[email protected]> Cc: Paul Turner <[email protected]> Cc: Quentin Perret <[email protected]> Cc: Thomas Gleixner <[email protected]> Cc: Todd Kjos <[email protected]> Cc: [email protected] Fixes: b5179ac ("sched/fair: Prepare to fix fairness problems on migration") Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Ingo Molnar <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit cf1015d upstream. Support additional DS4 model. Signed-off-by: Roderick Colenbrander <[email protected]> Reviewed-by: Benjamin Tissoires <[email protected]> Signed-off-by: Jiri Kosina <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit de66a1a upstream. Add support for USB based DS4 dongle device, which allows connecting a DS4 through Bluetooth, but hides Bluetooth from the host system. Signed-off-by: Roderick Colenbrander <[email protected]> Signed-off-by: Jiri Kosina <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 91a2968 upstream. The PCIE I/O and MEM resource allocation mechanism is that root bus goes through the following steps: 1. Check PCI bridges' range and computes I/O and Mem base/limits. 2. Sort all subordinate devices I/O and MEM resource requirements and allocate the resources and writes/updates subordinate devices' requirements to PCI bridges I/O and Mem MEM/limits registers. Currently, PCI Aardvark driver only handles the second step and lacks the first step, so there is an I/O and MEM resource allocation failure when using a PCI switch. This commit fixes that by sizing bridges before doing the resource allocation. Fixes: 8c39d71 ("PCI: aardvark: Add Aardvark PCI host controller driver") Signed-off-by: Zachary Zhang <[email protected]> [Thomas: edit commit log.] Signed-off-by: Thomas Petazzoni <[email protected]> Signed-off-by: Lorenzo Pieralisi <[email protected]> Cc: <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit a3b92ee upstream. Fix a build error due to missing virt_to_phys() Reported-by: kbuild test robot <[email protected]> Fixes: f0a1bf2 ("vmw_balloon: fix inflation with batching") Cc: [email protected] Cc: Xavier Deguillard <[email protected]> Signed-off-by: Nadav Amit <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 308aa2b upstream. Once the qp has been flushed, it cannot be flushed again. The user qp flush logic wasn't enforcing it however. The bug can cause touch-after-free crashes like: Unable to handle kernel paging request for data at address 0x000001ec Faulting instruction address: 0xc008000016069100 Oops: Kernel access of bad area, sig: 11 [Freescale#1] ... NIP [c008000016069100] flush_qp+0x80/0x480 [iw_cxgb4] LR [c00800001606cd6c] c4iw_modify_qp+0x71c/0x11d0 [iw_cxgb4] Call Trace: [c00800001606cd6c] c4iw_modify_qp+0x71c/0x11d0 [iw_cxgb4] [c00800001606e868] c4iw_ib_modify_qp+0x118/0x200 [iw_cxgb4] [c0080000119eae80] ib_security_modify_qp+0xd0/0x3d0 [ib_core] [c0080000119c4e24] ib_modify_qp+0xc4/0x2c0 [ib_core] [c008000011df0284] iwcm_modify_qp_err+0x44/0x70 [iw_cm] [c008000011df0fec] destroy_cm_id+0xcc/0x370 [iw_cm] [c008000011ed4358] rdma_destroy_id+0x3c8/0x520 [rdma_cm] [c0080000134b0540] ucma_close+0x90/0x1b0 [rdma_ucm] [c000000000444da4] __fput+0xe4/0x2f0 So fix flush_qp() to only flush the wq once. Cc: [email protected] Signed-off-by: Steve Wise <[email protected]> Signed-off-by: Jason Gunthorpe <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

This is the 4.9.130 stable release

commit 0711e8c upstream. Please note that below oops is from an older kernel, but the same race seems to be present in the upstream kernel too. ---8<--- The following panic was encountered during removing the ipmi_ssif module: [ 526.352555] Unable to handle kernel paging request at virtual address ffff000006923090 [ 526.360464] Mem abort info: [ 526.363257] ESR = 0x86000007 [ 526.366304] Exception class = IABT (current EL), IL = 32 bits [ 526.372221] SET = 0, FnV = 0 [ 526.375269] EA = 0, S1PTW = 0 [ 526.378405] swapper pgtable: 4k pages, 48-bit VAs, pgd = 000000008ae60416 [ 526.385185] [ffff000006923090] *pgd=000000bffcffe803, *pud=000000bffcffd803, *pmd=0000009f4731a003, *pte=0000000000000000 [ 526.396141] Internal error: Oops: 86000007 [#1] SMP [ 526.401008] Modules linked in: nls_iso8859_1 ipmi_devintf joydev input_leds ipmi_msghandler shpchp sch_fq_codel ib_iser rdma_cm iw_cm ib_cm ib_core iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi ip_tables x_tables autofs4 btrfs zstd_compress raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c raid1 raid0 multipath linear i2c_smbus hid_generic usbhid uas hid usb_storage ast aes_ce_blk i2c_algo_bit aes_ce_cipher qede ttm crc32_ce ptp crct10dif_ce drm_kms_helper ghash_ce syscopyarea sha2_ce sysfillrect sysimgblt pps_core fb_sys_fops sha256_arm64 sha1_ce mpt3sas qed drm raid_class ahci scsi_transport_sas libahci gpio_xlp i2c_xlp9xx aes_neon_bs aes_neon_blk crypto_simd cryptd aes_arm64 [last unloaded: ipmi_ssif] [ 526.468085] CPU: 125 PID: 0 Comm: swapper/125 Not tainted 4.15.0-35-generic #38~lp1775396+build.1 [ 526.476942] Hardware name: To be filled by O.E.M. Saber/Saber, BIOS 0ACKL022 08/14/2018 [ 526.484932] pstate: 00400009 (nzcv daif +PAN -UAO) [ 526.489713] pc : 0xffff000006923090 [ 526.493198] lr : call_timer_fn+0x34/0x178 [ 526.497194] sp : ffff000009b0bdd0 [ 526.500496] x29: ffff000009b0bdd0 x28: 0000000000000082 [ 526.505796] x27: 0000000000000002 x26: ffff000009515188 [ 526.511096] x25: ffff000009515180 x24: ffff0000090f1018 [ 526.516396] x23: ffff000009519660 x22: dead000000000200 [ 526.521696] x21: ffff000006923090 x20: 0000000000000100 [ 526.526995] x19: ffff809eeb466a40 x18: 0000000000000000 [ 526.532295] x17: 000000000000000e x16: 0000000000000007 [ 526.537594] x15: 0000000000000000 x14: 071c71c71c71c71c [ 526.542894] x13: 0000000000000000 x12: 0000000000000000 [ 526.548193] x11: 0000000000000001 x10: ffff000009b0be88 [ 526.553493] x9 : 0000000000000000 x8 : 0000000000000005 [ 526.558793] x7 : ffff80befc1f8528 x6 : 0000000000000020 [ 526.564092] x5 : 0000000000000040 x4 : 0000000020001b20 [ 526.569392] x3 : 0000000000000000 x2 : ffff809eeb466a40 [ 526.574692] x1 : ffff000006923090 x0 : ffff809eeb466a40 [ 526.579992] Process swapper/125 (pid: 0, stack limit = 0x000000002eb50acc) [ 526.586854] Call trace: [ 526.589289] 0xffff000006923090 [ 526.592419] expire_timers+0xc8/0x130 [ 526.596070] run_timer_softirq+0xec/0x1b0 [ 526.600070] __do_softirq+0x134/0x328 [ 526.603726] irq_exit+0xc8/0xe0 [ 526.606857] __handle_domain_irq+0x6c/0xc0 [ 526.610941] gic_handle_irq+0x84/0x188 [ 526.614679] el1_irq+0xe8/0x180 [ 526.617822] cpuidle_enter_state+0xa0/0x328 [ 526.621993] cpuidle_enter+0x34/0x48 [ 526.625564] call_cpuidle+0x44/0x70 [ 526.629040] do_idle+0x1b8/0x1f0 [ 526.632256] cpu_startup_entry+0x2c/0x30 [ 526.636174] secondary_start_kernel+0x11c/0x130 [ 526.640694] Code: bad PC value [ 526.643800] ---[ end trace d020b0b8417c2498 ]--- [ 526.648404] Kernel panic - not syncing: Fatal exception in interrupt [ 526.654778] SMP: stopping secondary CPUs [ 526.658734] Kernel Offset: disabled [ 526.662211] CPU features: 0x5800c38 [ 526.665688] Memory Limit: none [ 526.668768] ---[ end Kernel panic - not syncing: Fatal exception in interrupt Prevent mod_timer from arming a timer that was already removed by del_timer during module unload. Signed-off-by: Jan Glauber <[email protected]> Cc: <[email protected]> # 3.19 Signed-off-by: Corey Minyard <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 0711e8c upstream. Please note that below oops is from an older kernel, but the same race seems to be present in the upstream kernel too. ---8<--- The following panic was encountered during removing the ipmi_ssif module: [ 526.352555] Unable to handle kernel paging request at virtual address ffff000006923090 [ 526.360464] Mem abort info: [ 526.363257] ESR = 0x86000007 [ 526.366304] Exception class = IABT (current EL), IL = 32 bits [ 526.372221] SET = 0, FnV = 0 [ 526.375269] EA = 0, S1PTW = 0 [ 526.378405] swapper pgtable: 4k pages, 48-bit VAs, pgd = 000000008ae60416 [ 526.385185] [ffff000006923090] *pgd=000000bffcffe803, *pud=000000bffcffd803, *pmd=0000009f4731a003, *pte=0000000000000000 [ 526.396141] Internal error: Oops: 86000007 [Freescale#1] SMP [ 526.401008] Modules linked in: nls_iso8859_1 ipmi_devintf joydev input_leds ipmi_msghandler shpchp sch_fq_codel ib_iser rdma_cm iw_cm ib_cm ib_core iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi ip_tables x_tables autofs4 btrfs zstd_compress raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c raid1 raid0 multipath linear i2c_smbus hid_generic usbhid uas hid usb_storage ast aes_ce_blk i2c_algo_bit aes_ce_cipher qede ttm crc32_ce ptp crct10dif_ce drm_kms_helper ghash_ce syscopyarea sha2_ce sysfillrect sysimgblt pps_core fb_sys_fops sha256_arm64 sha1_ce mpt3sas qed drm raid_class ahci scsi_transport_sas libahci gpio_xlp i2c_xlp9xx aes_neon_bs aes_neon_blk crypto_simd cryptd aes_arm64 [last unloaded: ipmi_ssif] [ 526.468085] CPU: 125 PID: 0 Comm: swapper/125 Not tainted 4.15.0-35-generic Freescale#38~lp1775396+build.1 [ 526.476942] Hardware name: To be filled by O.E.M. Saber/Saber, BIOS 0ACKL022 08/14/2018 [ 526.484932] pstate: 00400009 (nzcv daif +PAN -UAO) [ 526.489713] pc : 0xffff000006923090 [ 526.493198] lr : call_timer_fn+0x34/0x178 [ 526.497194] sp : ffff000009b0bdd0 [ 526.500496] x29: ffff000009b0bdd0 x28: 0000000000000082 [ 526.505796] x27: 0000000000000002 x26: ffff000009515188 [ 526.511096] x25: ffff000009515180 x24: ffff0000090f1018 [ 526.516396] x23: ffff000009519660 x22: dead000000000200 [ 526.521696] x21: ffff000006923090 x20: 0000000000000100 [ 526.526995] x19: ffff809eeb466a40 x18: 0000000000000000 [ 526.532295] x17: 000000000000000e x16: 0000000000000007 [ 526.537594] x15: 0000000000000000 x14: 071c71c71c71c71c [ 526.542894] x13: 0000000000000000 x12: 0000000000000000 [ 526.548193] x11: 0000000000000001 x10: ffff000009b0be88 [ 526.553493] x9 : 0000000000000000 x8 : 0000000000000005 [ 526.558793] x7 : ffff80befc1f8528 x6 : 0000000000000020 [ 526.564092] x5 : 0000000000000040 x4 : 0000000020001b20 [ 526.569392] x3 : 0000000000000000 x2 : ffff809eeb466a40 [ 526.574692] x1 : ffff000006923090 x0 : ffff809eeb466a40 [ 526.579992] Process swapper/125 (pid: 0, stack limit = 0x000000002eb50acc) [ 526.586854] Call trace: [ 526.589289] 0xffff000006923090 [ 526.592419] expire_timers+0xc8/0x130 [ 526.596070] run_timer_softirq+0xec/0x1b0 [ 526.600070] __do_softirq+0x134/0x328 [ 526.603726] irq_exit+0xc8/0xe0 [ 526.606857] __handle_domain_irq+0x6c/0xc0 [ 526.610941] gic_handle_irq+0x84/0x188 [ 526.614679] el1_irq+0xe8/0x180 [ 526.617822] cpuidle_enter_state+0xa0/0x328 [ 526.621993] cpuidle_enter+0x34/0x48 [ 526.625564] call_cpuidle+0x44/0x70 [ 526.629040] do_idle+0x1b8/0x1f0 [ 526.632256] cpu_startup_entry+0x2c/0x30 [ 526.636174] secondary_start_kernel+0x11c/0x130 [ 526.640694] Code: bad PC value [ 526.643800] ---[ end trace d020b0b8417c2498 ]--- [ 526.648404] Kernel panic - not syncing: Fatal exception in interrupt [ 526.654778] SMP: stopping secondary CPUs [ 526.658734] Kernel Offset: disabled [ 526.662211] CPU features: 0x5800c38 [ 526.665688] Memory Limit: none [ 526.668768] ---[ end Kernel panic - not syncing: Fatal exception in interrupt Prevent mod_timer from arming a timer that was already removed by del_timer during module unload. Signed-off-by: Jan Glauber <[email protected]> Cc: <[email protected]> # 3.19 Signed-off-by: Corey Minyard <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

If read lock is called in mlb150_trans_complete_check, when the same lock is called from interrupt at the same time it will result in: [ 73.688839] WARNING: inconsistent lock state [ 73.693116] 5.2.0-rc3-next-20190607-20092-ge32edc4b91df-dirty Freescale#38 Not tainted [ 73.700256] -------------------------------- [ 73.704533] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-R} usage. [ 73.710546] mxc_mlb_test.ou/612 [HC0[0]:SC0[0]:HE1:SE1] takes: [ 73.716386] 554a05da (mlb_devinfo[1].tx_rbuf.rb_lock){-?--}, at: mxc_mlb150_ioctl+0x6a8/0x9a8 [ 73.724937] {IN-HARDIRQ-W} state was registered at: [ 73.729827] _raw_write_lock+0x28/0x38 [ 73.733669] mlb_tx_isr+0x54/0xf8 [ 73.737078] mlb_ahb_isr+0x98/0x124 [ 73.740668] __handle_irq_event_percpu+0x48/0x360 [ 73.745467] handle_irq_event_percpu+0x28/0x7c [ 73.750002] handle_irq_event+0x38/0x5c [ 73.753934] handle_fasteoi_irq+0xc0/0x17c [ 73.758125] generic_handle_irq+0x20/0x34 [ 73.762228] __handle_domain_irq+0x64/0xe0 [ 73.766422] gic_handle_irq+0x4c/0xa8 [ 73.770179] __irq_svc+0x70/0x98 [ 73.773506] cpuidle_enter_state+0x164/0x574 [ 73.777869] cpuidle_enter_state+0x164/0x574 [ 73.782232] cpuidle_enter+0x28/0x38 [ 73.785905] do_idle+0x220/0x2c0 [ 73.789226] cpu_startup_entry+0x18/0x20 [ 73.793247] start_kernel+0x3f4/0x4a0 Fix this by always using irq save rw locks in trans_complete_check. Signed-off-by: Clark Wang <[email protected]> Acked-by: Fugang Duan <[email protected]>

[ Upstream commit 623f279 ] If GPU components have failed to bind, shutdown callback would fail with the following backtrace. Add safeguard check to stop that oops from happening and allow the board to reboot. [ 66.617046] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 [ 66.626066] Mem abort info: [ 66.628939] ESR = 0x96000006 [ 66.632088] EC = 0x25: DABT (current EL), IL = 32 bits [ 66.637542] SET = 0, FnV = 0 [ 66.640688] EA = 0, S1PTW = 0 [ 66.643924] Data abort info: [ 66.646889] ISV = 0, ISS = 0x00000006 [ 66.650832] CM = 0, WnR = 0 [ 66.653890] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000107f81000 [ 66.660505] [0000000000000000] pgd=0000000100bb2003, p4d=0000000100bb2003, pud=0000000100897003, pmd=0000000000000000 [ 66.671398] Internal error: Oops: 96000006 [Freescale#1] PREEMPT SMP [ 66.677115] Modules linked in: [ 66.680261] CPU: 6 PID: 352 Comm: reboot Not tainted 5.11.0-rc2-00309-g79e3faa756b2 Freescale#38 [ 66.688473] Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT) [ 66.695347] pstate: 60400005 (nZCv daif +PAN -UAO -TCO BTYPE=--) [ 66.701507] pc : msm_atomic_commit_tail+0x78/0x4e0 [ 66.706437] lr : commit_tail+0xa4/0x184 [ 66.710381] sp : ffff8000108f3af0 [ 66.713791] x29: ffff8000108f3af0 x28: ffff418c44337000 [ 66.719242] x27: 0000000000000000 x26: ffff418c40a24490 [ 66.724693] x25: ffffd3a842a4f1a0 x24: 0000000000000008 [ 66.730146] x23: ffffd3a84313f030 x22: ffff418c444ce000 [ 66.735598] x21: ffff418c408a4980 x20: 0000000000000000 [ 66.741049] x19: 0000000000000000 x18: ffff800010710fbc [ 66.746500] x17: 000000000000000c x16: 0000000000000001 [ 66.751954] x15: 0000000000010008 x14: 0000000000000068 [ 66.757405] x13: 0000000000000001 x12: 0000000000000000 [ 66.762855] x11: 0000000000000001 x10: 00000000000009b0 [ 66.768306] x9 : ffffd3a843192000 x8 : ffff418c44337000 [ 66.773757] x7 : 0000000000000000 x6 : 00000000a401b34e [ 66.779210] x5 : 00ffffffffffffff x4 : 0000000000000000 [ 66.784660] x3 : 0000000000000000 x2 : ffff418c444ce000 [ 66.790111] x1 : ffffd3a841dce530 x0 : ffff418c444cf000 [ 66.795563] Call trace: [ 66.798075] msm_atomic_commit_tail+0x78/0x4e0 [ 66.802633] commit_tail+0xa4/0x184 [ 66.806217] drm_atomic_helper_commit+0x160/0x390 [ 66.811051] drm_atomic_commit+0x4c/0x60 [ 66.815082] drm_atomic_helper_disable_all+0x1f4/0x210 [ 66.820355] drm_atomic_helper_shutdown+0x80/0x130 [ 66.825276] msm_pdev_shutdown+0x14/0x20 [ 66.829303] platform_shutdown+0x28/0x40 [ 66.833330] device_shutdown+0x158/0x330 [ 66.837357] kernel_restart+0x40/0xa0 [ 66.841122] __do_sys_reboot+0x228/0x250 [ 66.845148] __arm64_sys_reboot+0x28/0x34 [ 66.849264] el0_svc_common.constprop.0+0x74/0x190 [ 66.854187] do_el0_svc+0x24/0x90 [ 66.857595] el0_svc+0x14/0x20 [ 66.860739] el0_sync_handler+0x1a4/0x1b0 [ 66.864858] el0_sync+0x174/0x180 [ 66.868269] Code: 1ac020a0 2a000273 eb02007f 54ffff01 (f9400285) [ 66.874525] ---[ end trace 20dedb2a3229fec8 ]--- Fixes: 9d5cbf5 ("drm/msm: add shutdown support for display platform_driver") Signed-off-by: Dmitry Baryshkov <[email protected]> Signed-off-by: Fabio Estevam <[email protected]> Signed-off-by: Rob Clark <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

commit ba7542e upstream. This patch fixes a memory corruption that occurred in the nand_scan() path for Hynix nand device. On boot, for Hynix nand device will panic at a weird place: | Unable to handle kernel NULL pointer dereference at virtual address 00000070 | [00000070] *pgd=00000000 | Internal error: Oops: 5 [Freescale#1] PREEMPT SMP ARM | Modules linked in: | CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.17.0-01473-g13ae1769cfb0 Freescale#38 | Hardware name: Generic DT based system | PC is at nandc_set_reg+0x8/0x1c | LR is at qcom_nandc_command+0x20c/0x5d0 | pc : [<c088b74c>] lr : [<c088d9c8>] psr: 00000113 | sp : c14adc5 ip : c14ee208 fp : c0cc970c | r10: 000000a3 r9 : 00000000 r8 : 00000040 | r7 : c16f6a00 r6 : 00000090 r5 : 00000004 r4 :c14ee040 | r3 : 00000000 r2 : 0000000b r1 : 00000000 r0 :c14ee040 | Flags: nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none | Control: 10c5387d Table: 8020406a DAC: 00000051 | Register r0 information: slab kmalloc-2k start c14ee000 pointer offset 64 size 2048 | Process swapper/0 (pid: 1, stack limit = 0x(ptrval)) | nandc_set_reg from qcom_nandc_command+0x20c/0x5d0 | qcom_nandc_command from nand_readid_op+0x198/0x1e8 | nand_readid_op from hynix_nand_has_valid_jedecid+0x30/0x78 | hynix_nand_has_valid_jedecid from hynix_nand_init+0xb8/0x454 | hynix_nand_init from nand_scan_with_ids+0xa30/0x14a8 | nand_scan_with_ids from qcom_nandc_probe+0x648/0x7b0 | qcom_nandc_probe from platform_probe+0x58/0xac The problem is that the nand_scan()'s qcom_nand_attach_chip callback is updating the nandc->max_cwperpage from 1 to 4 or 8 based on page size. This causes the sg_init_table of clear_bam_transaction() in the driver's qcom_nandc_command() to memset much more than what was initially allocated by alloc_bam_transaction(). This patch will update nandc->max_cwperpage 1 to 4 or 8 based on page size in qcom_nand_attach_chip call back after freeing the previously allocated memory for bam txn as per nandc->max_cwperpage = 1 and then again allocating bam txn as per nandc->max_cwperpage = 4 or 8 based on page size in qcom_nand_attach_chip call back itself. Cc: [email protected] Fixes: 6a3cec6 ("mtd: rawnand: qcom: convert driver to nand_scan()") Reported-by: Konrad Dybcio <[email protected]> Reviewed-by: Manivannan Sadhasivam <[email protected]> Co-developed-by: Sricharan R <[email protected]> Signed-off-by: Sricharan R <[email protected]> Signed-off-by: Md Sadre Alam <[email protected]> Signed-off-by: Miquel Raynal <[email protected]> Link: https://lore.kernel.org/linux-mtd/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit c2dbe32 upstream. If a non-root cgroup gets removed when there is a thread that registered trigger and is polling on a pressure file within the cgroup, the polling waitqueue gets freed in the following path: do_rmdir cgroup_rmdir kernfs_drain_open_files cgroup_file_release cgroup_pressure_release psi_trigger_destroy However, the polling thread still has a reference to the pressure file and will access the freed waitqueue when the file is closed or upon exit: fput ep_eventpoll_release ep_free ep_remove_wait_queue remove_wait_queue This results in use-after-free as pasted below. The fundamental problem here is that cgroup_file_release() (and consequently waitqueue's lifetime) is not tied to the file's real lifetime. Using wake_up_pollfree() here might be less than ideal, but it is in line with the comment at commit 42288cb ("wait: add wake_up_pollfree()") since the waitqueue's lifetime is not tied to file's one and can be considered as another special case. While this would be fixable by somehow making cgroup_file_release() be tied to the fput(), it would require sizable refactoring at cgroups or higher layer which might be more justifiable if we identify more cases like this. BUG: KASAN: use-after-free in _raw_spin_lock_irqsave+0x60/0xc0 Write of size 4 at addr ffff88810e625328 by task a.out/4404 CPU: 19 PID: 4404 Comm: a.out Not tainted 6.2.0-rc6 Freescale#38 Hardware name: Amazon EC2 c5a.8xlarge/, BIOS 1.0 10/16/2017 Call Trace: <TASK> dump_stack_lvl+0x73/0xa0 print_report+0x16c/0x4e0 kasan_report+0xc3/0xf0 kasan_check_range+0x2d2/0x310 _raw_spin_lock_irqsave+0x60/0xc0 remove_wait_queue+0x1a/0xa0 ep_free+0x12c/0x170 ep_eventpoll_release+0x26/0x30 __fput+0x202/0x400 task_work_run+0x11d/0x170 do_exit+0x495/0x1130 do_group_exit+0x100/0x100 get_signal+0xd67/0xde0 arch_do_signal_or_restart+0x2a/0x2b0 exit_to_user_mode_prepare+0x94/0x100 syscall_exit_to_user_mode+0x20/0x40 do_syscall_64+0x52/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd </TASK> Allocated by task 4404: kasan_set_track+0x3d/0x60 __kasan_kmalloc+0x85/0x90 psi_trigger_create+0x113/0x3e0 pressure_write+0x146/0x2e0 cgroup_file_write+0x11c/0x250 kernfs_fop_write_iter+0x186/0x220 vfs_write+0x3d8/0x5c0 ksys_write+0x90/0x110 do_syscall_64+0x43/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd Freed by task 4407: kasan_set_track+0x3d/0x60 kasan_save_free_info+0x27/0x40 ____kasan_slab_free+0x11d/0x170 slab_free_freelist_hook+0x87/0x150 __kmem_cache_free+0xcb/0x180 psi_trigger_destroy+0x2e8/0x310 cgroup_file_release+0x4f/0xb0 kernfs_drain_open_files+0x165/0x1f0 kernfs_drain+0x162/0x1a0 __kernfs_remove+0x1fb/0x310 kernfs_remove_by_name_ns+0x95/0xe0 cgroup_addrm_files+0x67f/0x700 cgroup_destroy_locked+0x283/0x3c0 cgroup_rmdir+0x29/0x100 kernfs_iop_rmdir+0xd1/0x140 vfs_rmdir+0xfe/0x240 do_rmdir+0x13d/0x280 __x64_sys_rmdir+0x2c/0x30 do_syscall_64+0x43/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd Fixes: 0e94682 ("psi: introduce psi monitor") Signed-off-by: Munehisa Kamata <[email protected]> Signed-off-by: Mengchi Cheng <[email protected]> Signed-off-by: Ingo Molnar <[email protected]> Acked-by: Suren Baghdasaryan <[email protected]> Acked-by: Peter Zijlstra <[email protected]> Cc: [email protected] Link: https://lore.kernel.org/lkml/[email protected]/ Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit efdde3d ] There is case as below could trigger kernel dump: Use U-Boot to start remote processor(rproc) with resource table published to a fixed address by rproc. After Kernel boots up, stop the rproc, load a new firmware which doesn't have resource table ,and start rproc. When starting rproc with a firmware not have resource table, `memcpy(loaded_table, rproc->cached_table, rproc->table_sz)` will trigger dump, because rproc->cache_table is set to NULL during the last stop operation, but rproc->table_sz is still valid. This issue is found on i.MX8MP and i.MX9. Dump as below: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Mem abort info: ESR = 0x0000000096000004 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x04: level 0 translation fault Data abort info: ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 CM = 0, WnR = 0, TnD = 0, TagAccess = 0 GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=000000010af63000 [0000000000000000] pgd=0000000000000000, p4d=0000000000000000 Internal error: Oops: 0000000096000004 [Freescale#1] PREEMPT SMP Modules linked in: CPU: 2 UID: 0 PID: 1060 Comm: sh Not tainted 6.14.0-rc7-next-20250317-dirty Freescale#38 Hardware name: NXP i.MX8MPlus EVK board (DT) pstate: a0000005 (NzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : __pi_memcpy_generic+0x110/0x22c lr : rproc_start+0x88/0x1e0 Call trace: __pi_memcpy_generic+0x110/0x22c (P) rproc_boot+0x198/0x57c state_store+0x40/0x104 dev_attr_store+0x18/0x2c sysfs_kf_write+0x7c/0x94 kernfs_fop_write_iter+0x120/0x1cc vfs_write+0x240/0x378 ksys_write+0x70/0x108 __arm64_sys_write+0x1c/0x28 invoke_syscall+0x48/0x10c el0_svc_common.constprop.0+0xc0/0xe0 do_el0_svc+0x1c/0x28 el0_svc+0x30/0xcc el0t_64_sync_handler+0x10c/0x138 el0t_64_sync+0x198/0x19c Clear rproc->table_sz to address the issue. Fixes: 9dc9507 ("remoteproc: Properly deal with the resource table when detaching") Signed-off-by: Peng Fan <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Bjorn Andersson <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit efdde3d ] There is case as below could trigger kernel dump: Use U-Boot to start remote processor(rproc) with resource table published to a fixed address by rproc. After Kernel boots up, stop the rproc, load a new firmware which doesn't have resource table ,and start rproc. When starting rproc with a firmware not have resource table, `memcpy(loaded_table, rproc->cached_table, rproc->table_sz)` will trigger dump, because rproc->cache_table is set to NULL during the last stop operation, but rproc->table_sz is still valid. This issue is found on i.MX8MP and i.MX9. Dump as below: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Mem abort info: ESR = 0x0000000096000004 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x04: level 0 translation fault Data abort info: ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 CM = 0, WnR = 0, TnD = 0, TagAccess = 0 GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=000000010af63000 [0000000000000000] pgd=0000000000000000, p4d=0000000000000000 Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP Modules linked in: CPU: 2 UID: 0 PID: 1060 Comm: sh Not tainted 6.14.0-rc7-next-20250317-dirty #38 Hardware name: NXP i.MX8MPlus EVK board (DT) pstate: a0000005 (NzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : __pi_memcpy_generic+0x110/0x22c lr : rproc_start+0x88/0x1e0 Call trace: __pi_memcpy_generic+0x110/0x22c (P) rproc_boot+0x198/0x57c state_store+0x40/0x104 dev_attr_store+0x18/0x2c sysfs_kf_write+0x7c/0x94 kernfs_fop_write_iter+0x120/0x1cc vfs_write+0x240/0x378 ksys_write+0x70/0x108 __arm64_sys_write+0x1c/0x28 invoke_syscall+0x48/0x10c el0_svc_common.constprop.0+0xc0/0xe0 do_el0_svc+0x1c/0x28 el0_svc+0x30/0xcc el0t_64_sync_handler+0x10c/0x138 el0t_64_sync+0x198/0x19c Clear rproc->table_sz to address the issue. Fixes: 9dc9507 ("remoteproc: Properly deal with the resource table when detaching") Signed-off-by: Peng Fan <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Bjorn Andersson <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

There is case as below could trigger kernel dump: Use U-Boot to start remote processor(rproc) with resource table published to a fixed address by rproc. After Kernel boots up, stop the rproc, load a new firmware which doesn't have resource table ,and start rproc. When starting rproc with a firmware not have resource table, `memcpy(loaded_table, rproc->cached_table, rproc->table_sz)` will trigger dump, because rproc->cache_table is set to NULL during the last stop operation, but rproc->table_sz is still valid. This issue is found on i.MX8MP and i.MX9. Dump as below: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Mem abort info: ESR = 0x0000000096000004 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x04: level 0 translation fault Data abort info: ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 CM = 0, WnR = 0, TnD = 0, TagAccess = 0 GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=000000010af63000 [0000000000000000] pgd=0000000000000000, p4d=0000000000000000 Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP Modules linked in: CPU: 2 UID: 0 PID: 1060 Comm: sh Not tainted 6.14.0-rc7-next-20250317-dirty #38 Hardware name: NXP i.MX8MPlus EVK board (DT) pstate: a0000005 (NzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : __pi_memcpy_generic+0x110/0x22c lr : rproc_start+0x88/0x1e0 Call trace: __pi_memcpy_generic+0x110/0x22c (P) rproc_boot+0x198/0x57c state_store+0x40/0x104 dev_attr_store+0x18/0x2c sysfs_kf_write+0x7c/0x94 kernfs_fop_write_iter+0x120/0x1cc vfs_write+0x240/0x378 ksys_write+0x70/0x108 __arm64_sys_write+0x1c/0x28 invoke_syscall+0x48/0x10c el0_svc_common.constprop.0+0xc0/0xe0 do_el0_svc+0x1c/0x28 el0_svc+0x30/0xcc el0t_64_sync_handler+0x10c/0x138 el0t_64_sync+0x198/0x19c Clear rproc->table_sz to address the issue. While at here, also clear rproc->table_sz when rproc_fw_boot and rproc_detach. Fixes: 9dc9507 ("remoteproc: Properly deal with the resource table when detaching") Reported-by: Jacky Bai <[email protected]> Reviewed-by: Jacky Bai <[email protected]> Signed-off-by: Peng Fan <[email protected]>

[ Upstream commit e4a718a ] tee_shm_put have NULL pointer dereference: __optee_disable_shm_cache --> shm = reg_pair_to_ptr(...);//shm maybe return NULL tee_shm_free(shm); --> tee_shm_put(shm);//crash Add check in tee_shm_put to fix it. panic log: Unable to handle kernel paging request at virtual address 0000000000100cca Mem abort info: ESR = 0x0000000096000004 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x04: level 0 translation fault Data abort info: ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 CM = 0, WnR = 0, TnD = 0, TagAccess = 0 GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=0000002049d07000 [0000000000100cca] pgd=0000000000000000, p4d=0000000000000000 Internal error: Oops: 0000000096000004 [Freescale#1] SMP CPU: 2 PID: 14442 Comm: systemd-sleep Tainted: P OE ------- ---- 6.6.0-39-generic Freescale#38 Source Version: 938b255f6cb8817c95b0dd5c8c2944acfce94b07 Hardware name: greatwall GW-001Y1A-FTH, BIOS Great Wall BIOS V3.0 10/26/2022 pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : tee_shm_put+0x24/0x188 lr : tee_shm_free+0x14/0x28 sp : ffff001f98f9faf0 x29: ffff001f98f9faf0 x28: ffff0020df543cc0 x27: 0000000000000000 x26: ffff001f811344a0 x25: ffff8000818dac00 x24: ffff800082d8d048 x23: ffff001f850fcd18 x22: 0000000000000001 x21: ffff001f98f9fb88 x20: ffff001f83e76218 x19: ffff001f83e761e0 x18: 000000000000ffff x17: 303a30303a303030 x16: 0000000000000000 x15: 0000000000000003 x14: 0000000000000001 x13: 0000000000000000 x12: 0101010101010101 x11: 0000000000000001 x10: 0000000000000001 x9 : ffff800080e08d0c x8 : ffff001f98f9fb88 x7 : 0000000000000000 x6 : 0000000000000000 x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000 x2 : ffff001f83e761e0 x1 : 00000000ffff001f x0 : 0000000000100cca Call trace: tee_shm_put+0x24/0x188 tee_shm_free+0x14/0x28 __optee_disable_shm_cache+0xa8/0x108 optee_shutdown+0x28/0x38 platform_shutdown+0x28/0x40 device_shutdown+0x144/0x2b0 kernel_power_off+0x3c/0x80 hibernate+0x35c/0x388 state_store+0x64/0x80 kobj_attr_store+0x14/0x28 sysfs_kf_write+0x48/0x60 kernfs_fop_write_iter+0x128/0x1c0 vfs_write+0x270/0x370 ksys_write+0x6c/0x100 __arm64_sys_write+0x20/0x30 invoke_syscall+0x4c/0x120 el0_svc_common.constprop.0+0x44/0xf0 do_el0_svc+0x24/0x38 el0_svc+0x24/0x88 el0t_64_sync_handler+0x134/0x150 el0t_64_sync+0x14c/0x15 Fixes: dfd0743 ("tee: handle lookup of shm with reference count 0") Signed-off-by: Pei Xiao <[email protected]> Reviewed-by: Sumit Garg <[email protected]> Signed-off-by: Jens Wiklander <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit efdde3d ] There is case as below could trigger kernel dump: Use U-Boot to start remote processor(rproc) with resource table published to a fixed address by rproc. After Kernel boots up, stop the rproc, load a new firmware which doesn't have resource table ,and start rproc. When starting rproc with a firmware not have resource table, `memcpy(loaded_table, rproc->cached_table, rproc->table_sz)` will trigger dump, because rproc->cache_table is set to NULL during the last stop operation, but rproc->table_sz is still valid. This issue is found on i.MX8MP and i.MX9. Dump as below: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Mem abort info: ESR = 0x0000000096000004 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x04: level 0 translation fault Data abort info: ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 CM = 0, WnR = 0, TnD = 0, TagAccess = 0 GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=000000010af63000 [0000000000000000] pgd=0000000000000000, p4d=0000000000000000 Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP Modules linked in: CPU: 2 UID: 0 PID: 1060 Comm: sh Not tainted 6.14.0-rc7-next-20250317-dirty #38 Hardware name: NXP i.MX8MPlus EVK board (DT) pstate: a0000005 (NzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : __pi_memcpy_generic+0x110/0x22c lr : rproc_start+0x88/0x1e0 Call trace: __pi_memcpy_generic+0x110/0x22c (P) rproc_boot+0x198/0x57c state_store+0x40/0x104 dev_attr_store+0x18/0x2c sysfs_kf_write+0x7c/0x94 kernfs_fop_write_iter+0x120/0x1cc vfs_write+0x240/0x378 ksys_write+0x70/0x108 __arm64_sys_write+0x1c/0x28 invoke_syscall+0x48/0x10c el0_svc_common.constprop.0+0xc0/0xe0 do_el0_svc+0x1c/0x28 el0_svc+0x30/0xcc el0t_64_sync_handler+0x10c/0x138 el0t_64_sync+0x198/0x19c Clear rproc->table_sz to address the issue. Fixes: 9dc9507 ("remoteproc: Properly deal with the resource table when detaching") Signed-off-by: Peng Fan <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Bjorn Andersson <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit e4a718a ] tee_shm_put have NULL pointer dereference: __optee_disable_shm_cache --> shm = reg_pair_to_ptr(...);//shm maybe return NULL tee_shm_free(shm); --> tee_shm_put(shm);//crash Add check in tee_shm_put to fix it. panic log: Unable to handle kernel paging request at virtual address 0000000000100cca Mem abort info: ESR = 0x0000000096000004 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x04: level 0 translation fault Data abort info: ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 CM = 0, WnR = 0, TnD = 0, TagAccess = 0 GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=0000002049d07000 [0000000000100cca] pgd=0000000000000000, p4d=0000000000000000 Internal error: Oops: 0000000096000004 [Freescale#1] SMP CPU: 2 PID: 14442 Comm: systemd-sleep Tainted: P OE ------- ---- 6.6.0-39-generic Freescale#38 Source Version: 938b255f6cb8817c95b0dd5c8c2944acfce94b07 Hardware name: greatwall GW-001Y1A-FTH, BIOS Great Wall BIOS V3.0 10/26/2022 pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : tee_shm_put+0x24/0x188 lr : tee_shm_free+0x14/0x28 sp : ffff001f98f9faf0 x29: ffff001f98f9faf0 x28: ffff0020df543cc0 x27: 0000000000000000 x26: ffff001f811344a0 x25: ffff8000818dac00 x24: ffff800082d8d048 x23: ffff001f850fcd18 x22: 0000000000000001 x21: ffff001f98f9fb88 x20: ffff001f83e76218 x19: ffff001f83e761e0 x18: 000000000000ffff x17: 303a30303a303030 x16: 0000000000000000 x15: 0000000000000003 x14: 0000000000000001 x13: 0000000000000000 x12: 0101010101010101 x11: 0000000000000001 x10: 0000000000000001 x9 : ffff800080e08d0c x8 : ffff001f98f9fb88 x7 : 0000000000000000 x6 : 0000000000000000 x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000 x2 : ffff001f83e761e0 x1 : 00000000ffff001f x0 : 0000000000100cca Call trace: tee_shm_put+0x24/0x188 tee_shm_free+0x14/0x28 __optee_disable_shm_cache+0xa8/0x108 optee_shutdown+0x28/0x38 platform_shutdown+0x28/0x40 device_shutdown+0x144/0x2b0 kernel_power_off+0x3c/0x80 hibernate+0x35c/0x388 state_store+0x64/0x80 kobj_attr_store+0x14/0x28 sysfs_kf_write+0x48/0x60 kernfs_fop_write_iter+0x128/0x1c0 vfs_write+0x270/0x370 ksys_write+0x6c/0x100 __arm64_sys_write+0x20/0x30 invoke_syscall+0x4c/0x120 el0_svc_common.constprop.0+0x44/0xf0 do_el0_svc+0x24/0x38 el0_svc+0x24/0x88 el0t_64_sync_handler+0x134/0x150 el0t_64_sync+0x14c/0x15 Fixes: dfd0743 ("tee: handle lookup of shm with reference count 0") Signed-off-by: Pei Xiao <[email protected]> Reviewed-by: Sumit Garg <[email protected]> Signed-off-by: Jens Wiklander <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit e4a718a ] tee_shm_put have NULL pointer dereference: __optee_disable_shm_cache --> shm = reg_pair_to_ptr(...);//shm maybe return NULL tee_shm_free(shm); --> tee_shm_put(shm);//crash Add check in tee_shm_put to fix it. panic log: Unable to handle kernel paging request at virtual address 0000000000100cca Mem abort info: ESR = 0x0000000096000004 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x04: level 0 translation fault Data abort info: ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 CM = 0, WnR = 0, TnD = 0, TagAccess = 0 GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=0000002049d07000 [0000000000100cca] pgd=0000000000000000, p4d=0000000000000000 Internal error: Oops: 0000000096000004 [#1] SMP CPU: 2 PID: 14442 Comm: systemd-sleep Tainted: P OE ------- ---- 6.6.0-39-generic Freescale#38 Source Version: 938b255f6cb8817c95b0dd5c8c2944acfce94b07 Hardware name: greatwall GW-001Y1A-FTH, BIOS Great Wall BIOS V3.0 10/26/2022 pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : tee_shm_put+0x24/0x188 lr : tee_shm_free+0x14/0x28 sp : ffff001f98f9faf0 x29: ffff001f98f9faf0 x28: ffff0020df543cc0 x27: 0000000000000000 x26: ffff001f811344a0 x25: ffff8000818dac00 x24: ffff800082d8d048 x23: ffff001f850fcd18 x22: 0000000000000001 x21: ffff001f98f9fb88 x20: ffff001f83e76218 x19: ffff001f83e761e0 x18: 000000000000ffff x17: 303a30303a303030 x16: 0000000000000000 x15: 0000000000000003 x14: 0000000000000001 x13: 0000000000000000 x12: 0101010101010101 x11: 0000000000000001 x10: 0000000000000001 x9 : ffff800080e08d0c x8 : ffff001f98f9fb88 x7 : 0000000000000000 x6 : 0000000000000000 x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000 x2 : ffff001f83e761e0 x1 : 00000000ffff001f x0 : 0000000000100cca Call trace: tee_shm_put+0x24/0x188 tee_shm_free+0x14/0x28 __optee_disable_shm_cache+0xa8/0x108 optee_shutdown+0x28/0x38 platform_shutdown+0x28/0x40 device_shutdown+0x144/0x2b0 kernel_power_off+0x3c/0x80 hibernate+0x35c/0x388 state_store+0x64/0x80 kobj_attr_store+0x14/0x28 sysfs_kf_write+0x48/0x60 kernfs_fop_write_iter+0x128/0x1c0 vfs_write+0x270/0x370 ksys_write+0x6c/0x100 __arm64_sys_write+0x20/0x30 invoke_syscall+0x4c/0x120 el0_svc_common.constprop.0+0x44/0xf0 do_el0_svc+0x24/0x38 el0_svc+0x24/0x88 el0t_64_sync_handler+0x134/0x150 el0t_64_sync+0x14c/0x15 Fixes: dfd0743 ("tee: handle lookup of shm with reference count 0") Signed-off-by: Pei Xiao <[email protected]> Reviewed-by: Sumit Garg <[email protected]> Signed-off-by: Jens Wiklander <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit eedf3e3 ] ACPICA commit 1c28da2242783579d59767617121035dafba18c3 This was originally done in NetBSD: NetBSD/src@b69d1ac and is the correct alternative to the smattering of `memcpy`s I previously contributed to this repository. This also sidesteps the newly strict checks added in UBSAN: llvm/llvm-project@7926744 Before this change we see the following UBSAN stack trace in Fuchsia: #0 0x000021afcfdeca5e in acpi_rs_get_address_common(struct acpi_resource*, union aml_resource*) ../../third_party/acpica/source/components/resources/rsaddr.c:329 <platform-bus-x86.so>+0x6aca5e Freescale#1.2 0x000021982bc4af3c in ubsan_get_stack_trace() compiler-rt/lib/ubsan/ubsan_diag.cpp:41 <libclang_rt.asan.so>+0x41f3c Freescale#1.1 0x000021982bc4af3c in maybe_print_stack_trace() compiler-rt/lib/ubsan/ubsan_diag.cpp:51 <libclang_rt.asan.so>+0x41f3c Freescale#1 0x000021982bc4af3c in ~scoped_report() compiler-rt/lib/ubsan/ubsan_diag.cpp:395 <libclang_rt.asan.so>+0x41f3c Freescale#2 0x000021982bc4bb6f in handletype_mismatch_impl() compiler-rt/lib/ubsan/ubsan_handlers.cpp:137 <libclang_rt.asan.so>+0x42b6f Freescale#3 0x000021982bc4b723 in __ubsan_handle_type_mismatch_v1 compiler-rt/lib/ubsan/ubsan_handlers.cpp:142 <libclang_rt.asan.so>+0x42723 Freescale#4 0x000021afcfdeca5e in acpi_rs_get_address_common(struct acpi_resource*, union aml_resource*) ../../third_party/acpica/source/components/resources/rsaddr.c:329 <platform-bus-x86.so>+0x6aca5e Freescale#5 0x000021afcfdf2089 in acpi_rs_convert_aml_to_resource(struct acpi_resource*, union aml_resource*, struct acpi_rsconvert_info*) ../../third_party/acpica/source/components/resources/rsmisc.c:355 <platform-bus-x86.so>+0x6b2089 Freescale#6 0x000021afcfded169 in acpi_rs_convert_aml_to_resources(u8*, u32, u32, u8, void**) ../../third_party/acpica/source/components/resources/rslist.c:137 <platform-bus-x86.so>+0x6ad169 Freescale#7 0x000021afcfe2d24a in acpi_ut_walk_aml_resources(struct acpi_walk_state*, u8*, acpi_size, acpi_walk_aml_callback, void**) ../../third_party/acpica/source/components/utilities/utresrc.c:237 <platform-bus-x86.so>+0x6ed24a Freescale#8 0x000021afcfde66b7 in acpi_rs_create_resource_list(union acpi_operand_object*, struct acpi_buffer*) ../../third_party/acpica/source/components/resources/rscreate.c:199 <platform-bus-x86.so>+0x6a66b7 Freescale#9 0x000021afcfdf6979 in acpi_rs_get_method_data(acpi_handle, const char*, struct acpi_buffer*) ../../third_party/acpica/source/components/resources/rsutils.c:770 <platform-bus-x86.so>+0x6b6979 Freescale#10 0x000021afcfdf708f in acpi_walk_resources(acpi_handle, char*, acpi_walk_resource_callback, void*) ../../third_party/acpica/source/components/resources/rsxface.c:731 <platform-bus-x86.so>+0x6b708f Freescale#11 0x000021afcfa95dcf in acpi::acpi_impl::walk_resources(acpi::acpi_impl*, acpi_handle, const char*, acpi::Acpi::resources_callable) ../../src/devices/board/lib/acpi/acpi-impl.cc:41 <platform-bus-x86.so>+0x355dcf Freescale#12 0x000021afcfaa8278 in acpi::device_builder::gather_resources(acpi::device_builder*, acpi::Acpi*, fidl::any_arena&, acpi::Manager*, acpi::device_builder::gather_resources_callback) ../../src/devices/board/lib/acpi/device-builder.cc:84 <platform-bus-x86.so>+0x368278 Freescale#13 0x000021afcfbddb87 in acpi::Manager::configure_discovered_devices(acpi::Manager*) ../../src/devices/board/lib/acpi/manager.cc:75 <platform-bus-x86.so>+0x49db87 Freescale#14 0x000021afcf99091d in publish_acpi_devices(acpi::Manager*, zx_device_t*, zx_device_t*) ../../src/devices/board/drivers/x86/acpi-nswalk.cc:95 <platform-bus-x86.so>+0x25091d Freescale#15 0x000021afcf9c1d4e in x86::X86::do_init(x86::X86*) ../../src/devices/board/drivers/x86/x86.cc:60 <platform-bus-x86.so>+0x281d4e Freescale#16 0x000021afcf9e33ad in λ(x86::X86::ddk_init::(anon class)*) ../../src/devices/board/drivers/x86/x86.cc:77 <platform-bus-x86.so>+0x2a33ad Freescale#17 0x000021afcf9e313e in fit::internal::target<(lambda at../../src/devices/board/drivers/x86/x86.cc:76:19), false, false, std::__2::allocator<std::byte>, void>::invoke(void*) ../../sdk/lib/fit/include/lib/fit/internal/function.h:183 <platform-bus-x86.so>+0x2a313e Freescale#18 0x000021afcfbab4c7 in fit::internal::function_base<16UL, false, void(), std::__2::allocator<std::byte>>::invoke(const fit::internal::function_base<16UL, false, void (), std::__2::allocator<std::byte> >*) ../../sdk/lib/fit/include/lib/fit/internal/function.h:522 <platform-bus-x86.so>+0x46b4c7 Freescale#19 0x000021afcfbab342 in fit::function_impl<16UL, false, void(), std::__2::allocator<std::byte>>::operator()(const fit::function_impl<16UL, false, void (), std::__2::allocator<std::byte> >*) ../../sdk/lib/fit/include/lib/fit/function.h:315 <platform-bus-x86.so>+0x46b342 Freescale#20 0x000021afcfcd98c3 in async::internal::retained_task::Handler(async_dispatcher_t*, async_task_t*, zx_status_t) ../../sdk/lib/async/task.cc:24 <platform-bus-x86.so>+0x5998c3 Freescale#21 0x00002290f9924616 in λ(const driver_runtime::Dispatcher::post_task::(anon class)*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, zx_status_t) ../../src/devices/bin/driver_runtime/dispatcher.cc:789 <libdriver_runtime.so>+0x10a616 Freescale#22 0x00002290f9924323 in fit::internal::target<(lambda at../../src/devices/bin/driver_runtime/dispatcher.cc:788:7), true, false, std::__2::allocator<std::byte>, void, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request>>, int>::invoke(void*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int) ../../sdk/lib/fit/include/lib/fit/internal/function.h:128 <libdriver_runtime.so>+0x10a323 Freescale#23 0x00002290f9904b76 in fit::internal::function_base<24UL, true, void(std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request>>, int), std::__2::allocator<std::byte>>::invoke(const fit::internal::function_base<24UL, true, void (std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int), std::__2::allocator<std::byte> >*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int) ../../sdk/lib/fit/include/lib/fit/internal/function.h:522 <libdriver_runtime.so>+0xeab76 Freescale#24 0x00002290f9904831 in fit::callback_impl<24UL, true, void(std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request>>, int), std::__2::allocator<std::byte>>::operator()(fit::callback_impl<24UL, true, void (std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int), std::__2::allocator<std::byte> >*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int) ../../sdk/lib/fit/include/lib/fit/function.h:471 <libdriver_runtime.so>+0xea831 Freescale#25 0x00002290f98d5adc in driver_runtime::callback_request::Call(driver_runtime::callback_request*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, zx_status_t) ../../src/devices/bin/driver_runtime/callback_request.h:74 <libdriver_runtime.so>+0xbbadc Freescale#26 0x00002290f98e1e58 in driver_runtime::Dispatcher::dispatch_callback(driver_runtime::Dispatcher*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >) ../../src/devices/bin/driver_runtime/dispatcher.cc:1248 <libdriver_runtime.so>+0xc7e58 Freescale#27 0x00002290f98e4159 in driver_runtime::Dispatcher::dispatch_callbacks(driver_runtime::Dispatcher*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../src/devices/bin/driver_runtime/dispatcher.cc:1308 <libdriver_runtime.so>+0xca159 Freescale#28 0x00002290f9918414 in λ(const driver_runtime::Dispatcher::create_with_adder::(anon class)*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../src/devices/bin/driver_runtime/dispatcher.cc:353 <libdriver_runtime.so>+0xfe414 Freescale#29 0x00002290f991812d in fit::internal::target<(lambda at../../src/devices/bin/driver_runtime/dispatcher.cc:351:7), true, false, std::__2::allocator<std::byte>, void, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter>>, fbl::ref_ptr<driver_runtime::Dispatcher>>::invoke(void*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../sdk/lib/fit/include/lib/fit/internal/function.h:128 <libdriver_runtime.so>+0xfe12d Freescale#30 0x00002290f9906fc7 in fit::internal::function_base<8UL, true, void(std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter>>, fbl::ref_ptr<driver_runtime::Dispatcher>), std::__2::allocator<std::byte>>::invoke(const fit::internal::function_base<8UL, true, void (std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>), std::__2::allocator<std::byte> >*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../sdk/lib/fit/include/lib/fit/internal/function.h:522 <libdriver_runtime.so>+0xecfc7 Freescale#31 0x00002290f9906c66 in fit::function_impl<8UL, true, void(std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter>>, fbl::ref_ptr<driver_runtime::Dispatcher>), std::__2::allocator<std::byte>>::operator()(const fit::function_impl<8UL, true, void (std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>), std::__2::allocator<std::byte> >*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../sdk/lib/fit/include/lib/fit/function.h:315 <libdriver_runtime.so>+0xecc66 Freescale#32 0x00002290f98e73d9 in driver_runtime::Dispatcher::event_waiter::invoke_callback(driver_runtime::Dispatcher::event_waiter*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../src/devices/bin/driver_runtime/dispatcher.h:543 <libdriver_runtime.so>+0xcd3d9 Freescale#33 0x00002290f98e700d in driver_runtime::Dispatcher::event_waiter::handle_event(std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, async_dispatcher_t*, async::wait_base*, zx_status_t, zx_packet_signal_t const*) ../../src/devices/bin/driver_runtime/dispatcher.cc:1442 <libdriver_runtime.so>+0xcd00d Freescale#34 0x00002290f9918983 in async_loop_owned_event_handler<driver_runtime::Dispatcher::event_waiter>::handle_event(async_loop_owned_event_handler<driver_runtime::Dispatcher::event_waiter>*, async_dispatcher_t*, async::wait_base*, zx_status_t, zx_packet_signal_t const*) ../../src/devices/bin/driver_runtime/async_loop_owned_event_handler.h:59 <libdriver_runtime.so>+0xfe983 Freescale#35 0x00002290f9918b9e in async::wait_method<async_loop_owned_event_handler<driver_runtime::Dispatcher::event_waiter>, &async_loop_owned_event_handler<driver_runtime::Dispatcher::event_waiter>::handle_event>::call_handler(async_dispatcher_t*, async_wait_t*, zx_status_t, zx_packet_signal_t const*) ../../sdk/lib/async/include/lib/async/cpp/wait.h:201 <libdriver_runtime.so>+0xfeb9e Freescale#36 0x00002290f99bf509 in async_loop_dispatch_wait(async_loop_t*, async_wait_t*, zx_status_t, zx_packet_signal_t const*) ../../sdk/lib/async-loop/loop.c:394 <libdriver_runtime.so>+0x1a5509 Freescale#37 0x00002290f99b9958 in async_loop_run_once(async_loop_t*, zx_time_t) ../../sdk/lib/async-loop/loop.c:343 <libdriver_runtime.so>+0x19f958 Freescale#38 0x00002290f99b9247 in async_loop_run(async_loop_t*, zx_time_t, _Bool) ../../sdk/lib/async-loop/loop.c:301 <libdriver_runtime.so>+0x19f247 Freescale#39 0x00002290f99ba962 in async_loop_run_thread(void*) ../../sdk/lib/async-loop/loop.c:860 <libdriver_runtime.so>+0x1a0962 Freescale#40 0x000041afd176ef30 in start_c11(void*) ../../zircon/third_party/ulib/musl/pthread/pthread_create.c:63 <libc.so>+0x84f30 Freescale#41 0x000041afd18a448d in thread_trampoline(uintptr_t, uintptr_t) ../../zircon/system/ulib/runtime/thread.cc:100 <libc.so>+0x1ba48d Link: acpica/acpica@1c28da22 Signed-off-by: Rafael J. Wysocki <[email protected]> Link: https://patch.msgid.link/[email protected] Signed-off-by: Tamir Duberstein <[email protected]> [ rjw: Pick up the tag from Tamir ] Signed-off-by: Rafael J. Wysocki <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit e4a718a ] tee_shm_put have NULL pointer dereference: __optee_disable_shm_cache --> shm = reg_pair_to_ptr(...);//shm maybe return NULL tee_shm_free(shm); --> tee_shm_put(shm);//crash Add check in tee_shm_put to fix it. panic log: Unable to handle kernel paging request at virtual address 0000000000100cca Mem abort info: ESR = 0x0000000096000004 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x04: level 0 translation fault Data abort info: ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 CM = 0, WnR = 0, TnD = 0, TagAccess = 0 GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=0000002049d07000 [0000000000100cca] pgd=0000000000000000, p4d=0000000000000000 Internal error: Oops: 0000000096000004 [Freescale#1] SMP CPU: 2 PID: 14442 Comm: systemd-sleep Tainted: P OE ------- ---- 6.6.0-39-generic Freescale#38 Source Version: 938b255f6cb8817c95b0dd5c8c2944acfce94b07 Hardware name: greatwall GW-001Y1A-FTH, BIOS Great Wall BIOS V3.0 10/26/2022 pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : tee_shm_put+0x24/0x188 lr : tee_shm_free+0x14/0x28 sp : ffff001f98f9faf0 x29: ffff001f98f9faf0 x28: ffff0020df543cc0 x27: 0000000000000000 x26: ffff001f811344a0 x25: ffff8000818dac00 x24: ffff800082d8d048 x23: ffff001f850fcd18 x22: 0000000000000001 x21: ffff001f98f9fb88 x20: ffff001f83e76218 x19: ffff001f83e761e0 x18: 000000000000ffff x17: 303a30303a303030 x16: 0000000000000000 x15: 0000000000000003 x14: 0000000000000001 x13: 0000000000000000 x12: 0101010101010101 x11: 0000000000000001 x10: 0000000000000001 x9 : ffff800080e08d0c x8 : ffff001f98f9fb88 x7 : 0000000000000000 x6 : 0000000000000000 x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000 x2 : ffff001f83e761e0 x1 : 00000000ffff001f x0 : 0000000000100cca Call trace: tee_shm_put+0x24/0x188 tee_shm_free+0x14/0x28 __optee_disable_shm_cache+0xa8/0x108 optee_shutdown+0x28/0x38 platform_shutdown+0x28/0x40 device_shutdown+0x144/0x2b0 kernel_power_off+0x3c/0x80 hibernate+0x35c/0x388 state_store+0x64/0x80 kobj_attr_store+0x14/0x28 sysfs_kf_write+0x48/0x60 kernfs_fop_write_iter+0x128/0x1c0 vfs_write+0x270/0x370 ksys_write+0x6c/0x100 __arm64_sys_write+0x20/0x30 invoke_syscall+0x4c/0x120 el0_svc_common.constprop.0+0x44/0xf0 do_el0_svc+0x24/0x38 el0_svc+0x24/0x88 el0t_64_sync_handler+0x134/0x150 el0t_64_sync+0x14c/0x15 Fixes: dfd0743 ("tee: handle lookup of shm with reference count 0") Signed-off-by: Pei Xiao <[email protected]> Reviewed-by: Sumit Garg <[email protected]> Signed-off-by: Jens Wiklander <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

Shubhrajyoti Datta and others added 30 commits September 19, 2018 22:47

Li Dongyang and others added 10 commits September 29, 2018 03:07

Linux 4.9.130

46f9f7c

Merge tag 'v4.9.130' into 4.9-2.3.x-imx

c98b0c5

This is the 4.9.130 stable release

otavio merged commit 5f3fecb into Freescale:4.9-2.3.x-imx Oct 2, 2018

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Merge v4.9.130 into 4.9-2.3.x imx#38

Merge v4.9.130 into 4.9-2.3.x imx#38
otavio merged 226 commits intoFreescale:4.9-2.3.x-imxfrom
gibsson:4.9-2.3.x-imx

gibsson commented Oct 2, 2018

Uh oh!

Reviewers

Assignees

Labels

Projects

Milestone

Development

Uh oh!

20 participants

Conversation

gibsson commented Oct 2, 2018

Uh oh!

Reviewers

Assignees

Labels

Projects

Milestone

Development

Uh oh!

20 participants