ラグ端子の英語

ラグ端子１は、脚部４、５及び半田付け突起９をプリント基板３０に半田付けされる。例文帳に追加

The lug terminal1 has leg parts 4, 5 and a soldering projection 9 to be soldered to a printed-circuit board 30. - 特許庁

ネジ座部１０１下面に設けられた実装端子１０５とプリント基板１１０の上面の間に半田付けがなされ、ラグ端子１００がプリント基板１１０に固定される。例文帳に追加

Soldering is applied between a mounted terminal 105 provided on the lower face of the screw seat part 101 and the upper face of the printed board 110 to fix the lug terminal 100 to the printed board 110. - 特許庁

部品同士等の接触による樹脂部の破損を防止することと、ラグ端子とコネクタを抜き差しする際の樹脂部の破損による、ラグ部の樹脂部からの脱落を防止することとを目的とする。例文帳に追加

To prevent damage in a resin part due to contact of a part with another one or the like, and also to prevent falling-off of a lug part from the resin part due to the damage of the resin part caused when a lug terminal is put in and pulled out of a connector. - 特許庁

導電性を有する帯状の端子部材１２の基端部に形成したラグ１３を振動板８の内周部近傍の裏面から表面側に突出せしめて固定し、該ラグ１３にボイスコイルのリード１０を接続する。例文帳に追加

A lug 13, formed at a base end of a conductive strip terminal member 12, is projected from a rear face in the vicinity of an inner circumference of a diaphragm 8 to a front side and fixed and a lead wire 10 of a vice coil is connected to the lug 13. - 特許庁

プリント基板上における取り付けや製造時に方向の制約がなく、プリント基板上における取り付けや製造が容易なラグ端子を提供する例文帳に追加

To provide a lug terminal which is free of directional restriction, when it is mounted on a printed board and manufactured, and which is easy to mount on the printed board and to manufacture. - 特許庁

半田付け後の経時変化により半田やせが発生しても、スペーシング突起８がラグ端子１とプリント基板３０との間隔が縮まるのを防止する。例文帳に追加

Even if solder wear occurs due to the change with the passage of time after soldering, the spacing projection 8 prevents shrinking of the spacing between the lug terminal 1 and the printed-circuit board 30. - 特許庁

固定端子部１２５は、カバー部材１２０の側板部１２３に切り起して形成してあり、ラグ部１２６、１２７を有し、断面が略台形である。例文帳に追加

The fixed terminal 125 is formed at a side plate 123 of a cover member 120 by being cut and raised, and has lugs 126, 127 and an approximately trapezoidal cross section. - 特許庁

ラグ端子１０の第１延出部１６の先端には先端凹部１８が形成されており、第２延出部２０にはサイド凹部２２が設けられている。例文帳に追加

A tip recessed part 18 is formed at a tip of a first extension part 16 of this lug terminal 10; and side recessed parts 22 are formed on second extension parts 20. - 特許庁